550344

DeWalt DCF835 T 10 Manual

39
Zoom out
Zoom in
Previous page
1/180
Next page
ENGLISH
37
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the
belt hook or bit clip, use only the screw (i) that is
provided. Be sure to securely tighten the screw.
The belt hook (h) and bit clip (j) can be be attached
to either side of the tool using only the screw (i)
provided, to accommodate left- or right-handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(i) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (fi g. 1, 4)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (k).
Variable Speed Trigger Switch (fi g. 1)
To turn the tool on, squeeze the trigger switch (a). To
turn the tool off, release the trigger switch. Your tool
is equipped with a brake. The chuck will stop when
the trigger switch is fully released.
The variable speed switch enables you to start
the application at a slow speed. The further you
squeeze the trigger, the faster the tool will operate.
For maximum tool life, use variable speed only for
starting holes or fasteners.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fi g. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool. The center
position of the control button locks the tool in the off
position. When changing the position of the control
button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up.
This is normal and does not indicate a problem.
Worklights (fi g. 1)
There are three worklights (g) located around the
chuck collar (c). The worklights will be activated
when the trigger switch is squeezed.
When the trigger is released the worklight will stay
illuminated for up to 20 seconds.
NOTE: The worklights are for lighting the immediate
work surface and are not intended to be used as a
flashlight.
Quick-Release Chuck (fi g. 1, 3)
DCF835, DCF885
NOTE: The chuck accepts 6.35mm (1/4") hex
accessories and 25.4mm (1") bit tips only. Using
25.4mm (1") bits allows better access in tight
spaces.
Place the forward/reverse button (b) in the locked
off (center) position or remove battery pack before
changing accessories.
To install an accessory, push accessory to fully insert
into chuck. The chuck collar does not need to be
pulled up to lock accessory in place.
To remove an accessory, pull the chuck collar away
from the front of the tool. Remove the accessory
and release the collar.
Anvil with Detent Pin (Fig. 1)
DCF830, DCF880
WARNING: Use only impact
accessories. Non-impact accessories
may break and cause a hazardous
condition. Inspect accessory prior to
use to ensure that it contains no cracks.
CAUTION: Inspect anvils and detent
pins prior to use. Missing or damaged
items should be replaced before use.
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF835 T 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF835 T 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info