447014

DeWalt dc618 Manual

44
Zoom out
Zoom in
Previous page
1/184
Next page
ENGLISH
42
explanation of these functionalities, refer to the
relating instructions in this manual.
WARNING: The headlights are intended
for lighting the immediate work surface.
Do not use the headlights as the only
light source.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Proper Hand Position (fi g. 11)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle of the tool (t) as shown.
Preparing the Tool (fi g. 9)
1. Remove all nails from the magazine.
2. Lock the nail pusher (o) in the back position.
3. Check if the contact trip (e) and nail pusher (o)
can move freely.
4. Reload the nails to the magazine.
WARNING: Do not use the tool if the
contact trip or nail pusher cannot move
freely.
Actuating the Tool (fi g. 1)
The tool can be operated using one of two modes:
sequential action mode or bump action mode.
SEQUENTIAL ACTION MODE
The sequential action mode is used for intermittent
nailing when very careful and accurate placement is
desired.
1. Select the sequential action mode.
2. Release the contact trip lock (b).
3. Push the contact trip (e) against the work
surface.
4. Pull the trigger (a) to actuate the tool. Each
trigger pull with the contact trip pushed against
the work surface will drive one nail.
Bump Action (fi g. 1)
The bump action mode is used for rapid nailing on
flat, stationary surfaces.
1. Release the contact trip lock (b).
2. Select the bump action mode.
3. To drive a single nail: Operate the tool as
described for sequential action.
TO DRIVE SEVERAL NAILS
Pull the trigger (a) first, and then push the contact
trip (e) repeatedly against the work surface.
WARNING: Do not keep the trigger
depressed when the tool is not in use.
Keep the contact trip (b) in the locked
position to prevent accidental actuation
when the tool is not in use.
Clearing a Jammed Nail (fi g. 1, 10)
If a nail becomes jammed in the nosepiece, the
headlights (d) will blink continuously.
1. Remove the battery pack (i).
2. Engage the contact trip lock (b).
3. Remove all nails from the magazine (f).
4. Release the latch (r) on top of the nosepiece.
5. Retract the barrel (s) so the jammed nail is
exposed.
6. Remove the nail, using pliers if necessary.
7. If the driver blade is in the down position, insert
a screwdriver into the nosepiece and push the
blade back in position.
8. Lower the barrel back in place.
9. Re-engage the latch.
WARNING: If nails become jammed
in the nosepiece frequently, have the
toolserviced by an authorised DEWALT
service centre.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dc618 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc618 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 9,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info