447014

DeWalt dc618 Manual

43
Zoom out
Zoom in
Previous page
1/184
Next page
ENGLISH
41
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the notch inside the tool’s handle with the
battery pack.
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (j) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Low Battery Indicator (fi g. 1)
The low battery indicator is an integrated feature in
the headlights (d). It will blink 4 times to indicate that
the battery pack needs to be recharged and the tool
will automatically shut down.
Switch off the tool and take out the battery pack (i)
to charge it as soon as the indicator blinks.
WARNING: The tool remains non-
operational as long as a low battery
pack is attached to it.
Mounting the Belt Hook (fi g. 3)
1. Insert the belt hook (h) into the mounting hole
on either side of the tool.
2. Pass the screw (n) through the mounting hole in
the opposite side. Tighten the screw.
Loading the Tool (fi g. 4)
The tool can be loaded using either of the below
methods.
LOCK AND LOAD METHOD
1. Lock the nail pusher (o) in the back position.
2. Select an appropriate collated nail stick. See
"Technical data".
3. Insert the nails into the loading slot in the
bottom of the magazine (f).
4. Unlatch the nail pusher by pulling rearward and
carefully slide the nail pusher forward to press
against the nails.
LOAD AND DRAW METHOD
1. Insert the nails into the loading slot in the
bottom of the magazine (f).
2. Draw the nail pusher (o) back until behind the
nails.
3. Release the nail pusher to press against the
nails.
UNLOADING THE TOOL
1. Lock the nail pusher (o) in the back position.
2. Remove the nails from the magazine (f).
Adjusting the Driving Depth (fi g. 5)
The driving depth can be adjusted to the type of
fastener used.
• Adjust the driving depth as required, choosing a
setting from 1 (shallow) to 6 (deep).
• To reduce the depth, turn the depth adjustment
wheel (c) clockwise.
• To increase the depth, turn the depth
adjustment wheel counterclockwise.
Selecting the Mode (fi g. 6)
• To select sequential action mode, slide the
mode selector switch (g) to the left.
• To select bump action mode, slide the mode
selector switch (g) to the right.
Contact Trip Lock (fi g. 7)
This tool is equipped with a contact trip lock-off (b)
which prevents the tool from fi ring a nail.
To release the contact trip lock (b), pull the switch
upward.
To engage the contact trip lock, push the switch
downward.
WARNING: Make sure the contact
trip lock (b) is engaged and the battery
pack is removed before making any
adjustments or when tool is not in
immediate use.
No-mark Tip (fi g. 8)
Place the no-mark tip (p) over the contact trip (e)
when the tool is used on wood.
Store the no-mark tip at the holder (q) whenever it is
not to be used.
WARNING: Make sure the contact trip
lock (b) is engaged and the battery pack
is removed before installing or removing
the no-mark tip.
Headlights (fi g. 1)
This tool has headlights (d) located on each side.
The headlights will light upon inserting the battery
pack and upon activating the trigger or releasing the
contact trip. The lights will automatically go off after
10 seconds of non-operation.
The headlights also function as a low battery
indicator and a jammed nail indicator. For a further
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dc618 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc618 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 9,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info