382886
40
Zoom out
Zoom in
Previous page
1/192
Next page
38
ENGLISH
Charging Procedure (fi g. A, B)
DANGER: Electrocution hazard.
230 volts present at charging terminals.
Do not probe with conductive objects.
Danger of electric shock or electrocution.
1. Plug the charger (15) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack into the charger. The
charger is equipped with a three-light fuel gauge
that will blink according to the state of charge of
the battery pack.
3. The completion of charge is indicated by the
three red lights remaining ON continuously. The
pack is fully charged and may be used at this
time or left on the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery for a minimum of
10 hours before first use.
Charging Process
Refer to the table below for the state of charge of the
battery pack.
State of charge
1 light blinking < 33%
1 light blinking, 1 light on 33–66%
1 light blinking, 2 lights on 66–99%
3 lights on 100%
Automatic Refresh
The automatic refresh mode will equalise or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed weekly
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place the battery in the
charger as usual. Leave the battery pack for at least
10 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery against
overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to
include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or
removing the battery from the charger may ignite
the dust or fumes.
• Charge the battery packs only in DEWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery pack
in locations where the temperature may reach
or exceed 40˚ C (such as outside sheds or
metal buildings in summer).
DANGER: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged, do not
insert into charger. Do not crush, drop
or damage battery pack. Do not use a
battery pack or charger that has received
a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with
a nail, hit with a hammer, stepped on).
Electric shock or electrocution may result.
Damaged battery packs should be
returned to service center for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt dc 300 kl qw at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc 300 kl qw in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 8,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info