Manual DeWalt dc 300 kl qw (page 38 of 192) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

382886

Zoom out

Zoom in

1/192

ENGLISH

Lower Guard Safety Instructions

a Check lower guard for proper closing

before each use. Do not operate the saw if

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position.

If saw is accidentally dropped, lower guard

may be bent. Raise the lower guard with the

retracting handle and make sure it moves freely

and does not touch the blade or any other part,

in all angles and depths of cut.

b Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use.

Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up

of debris.

c Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts”. Raise lower guard

by retracting handle and as soon as blade

enters the material, the lower guard must be

released.

For all other sawing, the lower guard should

operate automatically.

d Always observe that the lower guard is

covering the blade before placing saw down

on bench or ﬂ oor.

An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in

its path. Be aware of the time it takes for the

blade to stop after switch is released.

Additional safety instructions for circular saws

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Preferably wear a dust mask.

• Do not use blades of larger or smaller diameter

than recommended. For the proper blade

rating refer to the technical data. Use only the

blades speci ed in this manual, complying with

EN 847-1.

• Never use abrasive cut-off wheels.

Additional Safety Instructions for All

Saws with Riving Knife

a) Use the appropriate riving knife for the blade

being used. For the riving knife to work, it must

be thicker than the body of the blade but thinner

than the tooth set of the blade.

b) Adjust the riving knife as described in

this instruction manual. Incorrect spacing,

positioning and alignment can make the riving

knife ineffective in preventing kickback.

c) For the riving knife to work, it must be

engaged in the work piece. The riving knife is

ineffective in preventing kickback during short

cuts.

d) Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing rate

of a guard.

Residual Risks

The following risks are inherent to the use of circular

saws.

– Injuries caused by touching the rotating parts or

hot part of the tool.

In spite of the application of the relevant safety

regulations and the implementation of safety devices,

certain residual risks cannot be avoided. These are:

– Impairment of hearing .

– Risk of squeezing fingers when changing the

accessory.

– Health hazards caused by breathing dust

developed when working in wood.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dc 300 kl qw in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 8,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dc 300 kl qw Manual

Product: