79260

DeWalt DC 228 Manual

46
Zoom out
Zoom in
Previous page
1/204
Next page
44
ENGLISH
CAUTION: Never use standard chucks
in the hammerdrilling mode.
Replacing the dust cover (fi g. D)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
• Pull back the tool holder locking sleeve (15) and
pull the dust cover (7) off.
• Fit the new dust cover.
• Release the tool holder locking sleeve.
OPERATION
Instructions For Use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply only a gentle pressure to the tool
(approx. 5 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
• Do not drill or drive too deep to prevent
damage to the dust cover.
Always hold the tool fi rmly with both
hands and ensure a secure stance .
Always operate the tool with the side
handle properly mounted.
• If the cutting tool is no longer sharp,
replace with a new cutting tool.
Prior to Operation:
• Make sure your battery pack is (fully) charged.
• Make sure the battery pack is properly seated.
Proper Hand Position (fi g. I)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side
handle (9), with the other hand on the main handle
(10).
• To remove a bit pull back the tool holder locking
sleeve (15) and pull out the bit.
Fitting the side handle (fi g. E)
The side handle (9) can be fi tted to suit both
right-hand and left-hand users.
WARNING: Do not use the tool without
the side handle properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the left.
• For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fi g. F)
• Insert the required drill bit.
• Slacken the side handle (9).
• Fit the depth adjustment rod (8) through the
hole in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
Forward/reverse Slider (fi g. G)
• Push the forward/reverse slider (2) to the LH-side
for forward (RH) rotation. See arrows on tool.
• Push the forward/reverse slider (2) to the RH-
side for reverse (LH) rotation.
CAUTION: Always wait until the motor
has come to a complete standstill
before changing the direction of
rotation.
DC229, DC234 - Replacing the Tool Holder with
the Chuck (fi g. H)
• Turn the locking collar (6) into the unlocking
position and pull the tool holder (5) off.
• Push the chuck (16) onto the spindle and turn
the locking collar into the locking position.
• To replace the chuck with the tool holder, fi rst
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DC 228 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DC 228 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DC 228

DeWalt DC 228 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info