546481
29
Zoom out
Zoom in
Previous page
1/144
Next page
ENGLISH
27
Only connect this tool to an air supply where
the maximum allowable pressure of the tool
cannot be exceeded by more than 10%. In case
of higher pressures, a pressure reducing valve
including a downstream safety valve shall be
built into the compressed air supply.
Only use hoses with a rating exceeding the
maximum operating pressure of the tool.
To prevent an unnecessarily high noise level,
increased wear and resulting failures, the nailer
should be operated with the lowest pressure
required for the work process.
DO NOT use oxygen, combustible gases
or any other reactive gases for operating
compressed air. Danger of explosion and/or
serious personal injury may result.
Before transporting the tool, disconnect it from
the compressed air system, especially where
ladders are used or where unusual physical
posture is adopted while moving.
Disconnect the tool from the air supply when it
is not in use.
Avoid weakening or damaging the tool,
for example by:
punching or engraving
modifications not authorised by the
manufacturer
guiding against templates made of hard
material such as steel
dropping or pushing across the floor
applying excessive force of any kind
Do not use the equipment as a hammer.
WARNING! Keep the nailer, loaded or
unloaded, pointed away from yourself and
others. Serious personal injury may result.
While working, hold the tool in such a way that
no injuries can be caused to the head or to the
body in the event of a possible recoil due to a
disruption in the energy supply or hard areas
within the workpiece.
NEVER actuate the fastener driving tool into
free space.
In the work area, carry the tool at the workplace
using only one handle, and NEVER with the
trigger actuated.
Consider the conditions in the work area.
Fasteners can penetrate thin workpieces or slip
off corners and edges of the workpiece, and
thus put people at risk. The length of the nails
used should be no longer than the thickness of
the workpieces. If the nails are longer than the
workpiece thickness this could cause a rebound
of the nails if the workpiece is placed on a hard
surface e.g., concrete, steel.
Do not drive fasteners close to the dge of the
workpiece. ALWAYS keep a distance of at least
25 mm from the edge of the workpiece so nails
will not destroy the workpiece.
Do not drive fasteners on top of other fasteners.
Only use spare parts specified by the
manufacturer or his authorised agents.
Have repairs carried out only by the
manufacturer or authorised agents having due
regard to the information given in the manual
and using the appropriate tools and equipment.
Replacement of contact trip spring is
recommended every 3-4 years to ensure
personal safety.
Do not disassemble or block any parts of the
fastener driving tool such as the safety yoke.
Have the tool serviced properly and at regular
intervals.
ALWAYS wear safety gloves to reduce the risk
of personal injuries.
Residual Risks
The following risks are inherent to the use of
these machines:
Injuries caused by improper handling of
the tool.
Loss of control due to not grippring tool
firmly.
Muscle strain of arms and hands,
especially when working overhead.
Always take regular breaks when
working for long periods of time.
Do not use the tool while you are tired
or under influence of drugs, alcohol or
medication. A moment of inattention while
operating may result in serious personal
injury.
In spite of the application of the relevant
safety regulations and the implementation of
safety devices, certain residual risks cannot be
avoided.
These are:
Impairment of hearing. Under some
conditions and duration of use, noise
from this product may contribute to
hearing loss.
Loss of control caused by recoil.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D51850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51850 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info