546471

DeWalt D51430 T 2 Manual

24
Zoom out
Zoom in
Previous page
1/104
Next page
22
ENGLISH
Removing the trigger
• Disconnect the airline from the tool.
• Remove all fasteners from the magazine.
• Remove the rubber grommet (8) from the end of
the dowel pin (9).
• Remove the dowel pin.
• Remove the trigger assembly (10).
Fitting the trigger
• Insert the trigger assembly into the trigger cavity,
ensuring that the trigger spring (11) is properly
seated.
• Insert the dowel pin (9) through the tool frame,
contact trip guide and trigger assembly.
• Push the rubber grommet (8) onto the end of the
dowel pin.
Air fi tting (fi g. A)
These tools have a standard 3/8" pipe thread for the
air fi tting (7).
• Wrap the male end of the fi tting with Tefl on tape
to prevent air leaks.
• Screw the fi tting into the end cap and tighten fi rmly.
Loading the tool (fi g. C)
• Lock the magazine latch (6) in the back position.
• Select an appropriate collated fastener stick.
See “Technical data”.
• Place the collated fastener stick(s) onto the
magazine rail (11).
• Release the magazine latch by unlatching the
lever (6).
• Carefully slide the latch forward to press against
the fasteners.
Unloading the tool (fi g. C)
• Lock the magazine latch (6) in the back position.
• Remove the collated fastener stick(s) from the
magazine rail (11).
WARNING: Always disconnect the tool
from the air supply before loading or
unloading fasteners.
Adjusting the driving depth (fi g. D)
The driving depth can be adjusted to the type of
fastener used.
WARNING: To reduce risk of serious injury
from accidental actuation when attempting
to adjust depth, ALWAYS:
• Lock OFF trigger.
• Disconnect air supply.
• Avoid contact with trigger during
adjustments.
• To reduce the depth, rotate the depth setting
wheel (3) to the right.
• To increase the depth, rotate the depth setting
wheel (3) to the left.
Trigger lock (fi g. A)
This tool is equipped with a trigger lock-off switch
which prevents the tool from fi ring a fastener.
• To engage the trigger lock, push the switch (2) to
the right.
• To release the trigger lock, push the switch to the
center.
OPERATION
Instructions for use
WARNING: Always observe the safety
instructions and applicable regulations.
Proper Hand Position (fi g. F)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle (15).
Preparing the tool (fi g. A)
• Drain all condensation from the air compressor
tanks and hoses.
• Lubricate the tool. See “Maintenance”.
• Remove all fasteners from the magazine.
• Check if the contact trip (4) can move freely.
WARNING: Do not use the tool if the
contact trip cannot move freely.
• Check that the pressure of the air supply is below
the maximum recommended operating pressure.
• Connect the air hose to the fi tting on the tool.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D51430 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51430 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info