546471

DeWalt D51430 T 2 Manual

22
Zoom out
Zoom in
Previous page
1/104
Next page
20
ENGLISH
4. Store idle tools.
When not in use, tools must be stored in a dry
place and locked up securely, out of reach of
children.
5. Dress properly.
Do not wear loose clothing or jewellery. They
can be caught in moving parts. Preferably wear
rubber gloves and non-slip safety footwear. Wear
protective hair covering to keep long hair out of
the way.
6. Do not overreach.
Keep proper footing and balance at all times.
7. Stay alert.
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
8. Use appropriate tool.
The intended use is described in this instruction
manual. Do not force small tools or attachments
to do the job of a heavy-duty tool. The tool will
do the job better and safer at the rate for which it
was intended.
WARNING! The use of any accessory or
attachment or performance of any operation with
this tool, other than those recommended in this
instruction manual may present a risk of personal
injury.
9. Maintain tools with care.
Keep the tools in good condition and clean
for better and safer performance. Follow the
instructions for maintenance and changing
accessories. Keep all controls dry, clean and free
from oil and grease.
10. Check for damaged parts.
Before using the tool, carefully check it for damage
to ensure that it will operate properly and perform
its intended function. Check for misalignment and
seizure of moving parts, breakage of parts and
any other conditions that may affect its operation.
Have damaged guards or other defective parts
repaired or replaced as instructed.
11. Have your tool repaired by an authorized
D
EWALT repair agent.
This tool is in accordance with the relevant safety
regulations. To avoid danger, tools must only be
repaired by qualified technicians.
Additional safety instructions for pneumatic tools
• Use quick-action couplings for connection to
the compressed air system. The non-sealable
nipple must be fi tted to the tool in such a way
that no compressed air remains in the tool after
disconnection.
• Always use clean, dry compressed air. Do not
use oxygen or combustible gases as an energy
source for this tool.
• Only connect this tool to an air supply where
the maximum allowable pressure of the tool
cannot be exceeded by more than 10%. In case
of higher pressures, a pressure reducing valve
including a downstream safety valve shall be built
into the compressed air supply.
• Only use hoses with a rating exceeding the
maximum operating pressure of the tool.
• Before transporting the tool, disconnect it from
the compressed air system, especially where
ladders are used or where unusual physical
posture is adopted while moving.
• Disconnect the tool from the air supply when it is
not in use.
Additional safety instructions for fastener driving
tools
• Always wear safety glasses.
• Always wear ear protection.
• Never load fasteners with the trigger activated.
• Only use fasteners of the type specifi ed in the
manual.
• Do not use any stands for mounting the tool to
a support.
• Do not disassemble or block any parts of the
fastener driving tool such as the safety yoke.
• Prior to each operation check that the safety and
triggering mechanism is functioning properly and
that all nuts and bolts are tight.
• Do not use the equipment as a hammer.
• Never point any operational fastener driving tool
at yourself or at any other person. Do not use the
tool in applications requiring operation close to
the body.
• While working, hold the tool in such a way that
no injuries can be caused to the head or to the
body in the event of a possible recoil due to
a disruption in the energy supply or hard areas
within the workpiece.
• Never actuate the fastener driving tool into free
space.
• Consider the conditions in the work area.
Fasteners can penetrate thin workpieces or slip
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D51430 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51430 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info