Manual DeWalt D51275K T 3 (page 24 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546463

Zoom out

Zoom in

1/96

ENGLISH

• To drive several nails: Pull the trigger first, and

then push the contact trip repeatedly against the

work surface.

Do not keep the trigger depressed when

the tool is not in use. Keep the trigger

lock-off switch rotated to the right to

prevent accidental actuation when the

tool is not in use.

Clearing a jammed nail (fig. E)

If a nail becomes jammed in the nosepiece, follow

these instructions to remove the nail:

• Disconnect the airline from the tool.

• Lock the trigger with the trigger lock-off switch.

• Lock the nail pusher (11) in the back position.

• Flip up the front latch (12) and move the bracket

(13) out of the way so that barrel (14) can be

opened.

• Remove the bent nail, using pliers if necessary.

• If the driver blade is in the down position, push

the driver blade upward using a screwdriver.

• Close the barrel (14) and put the bracket (13)

back in position.

• Press the front latch (12) into the locked position.

• Connect the air hose to the fitting on the tool.

• Load nails into the magazine. See “Loading the

tool”.

• Unlatch the nail pusher by pushing forward and

carefully slide the nail pusher forward to press

against the nails.

If nails become jammed in the nosepiece

frequently, have the tool serviced by an

authorised DEWALT service centre.

Depth setting (fig. F)

Always disconnect the tool from the air

supply before adjusting the depth setting.

The depth that the nails are driven can be adjusted

using the depth adjustment on the nosepiece of

the tool.

• To reduce the depth, press the adjustment

button (15) and slide the slider switch (16)

downward.

• To increase the depth, press the adjustment

button (15) and slide the slider switch (16)

upward.

Belt/rafter hook

These tools have an integrated belt/rafter hook.

The hook can be rotated to either side of the tool

and can be folded out of the way when not in use.

To remove the belt/rafter hook:

• Remove the air hose from the fitting on the tool.

• Use pliers or a wrench to remove the nut for the

belt/rafter hook from the end cap of the tool.

• Remove the belt/rafter hook, washer and detent

spring.

Maintenance

Your DEWALT tool has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends on proper tool care and regular cleaning.

Perform the following maintenance operations every

day:

Lubricate tool with 5-7 drops of DEWALT

pneumatic tool oil

• Insert drops into the air fitting on the end cap of

the tool.

Drain all condensation from the air compressor

tanks and hoses

• Open petcocks or other drain valves on the

compressor tanks.

• Allow any accumulated water to drain from hoses.

Clean magazine, pusher, and contact trip

mechanism

• Clean by blowing with compressed air.

Ensure that all fasteners on the tool are tight and

undamaged

• Tighten loose fasteners using the appropriate tool.

D51256.P65 28-12-2001, 09:2124

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51275K T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D51275K T 3 Manual

Product: