546463
23
Zoom out
Zoom in
Previous page
1/96
Next page
23
ENGLISH
Instructions for use
Always observe the safety instructions
and applicable regulations.
Preparing the tool (fig. C)
Drain all condensation from the air compressor
tanks and hoses.
Lubricate the tool. See “Maintenance”.
Remove all nails from the magazine.
Lock the nail pusher (11) in the back position.
Check if the contact trip (3) and nail pusher (11)
can move freely.
Do not use the tool if the contact trip or
nail pusher cannot move freely.
Check that the pressure of the air supply is below
the maximum recommended operating pressure.
Connect the air hose to the fitting on the tool.
Check for audible leaks around valves and gaskets.
Never use a tool that leaks or has
damaged parts.
Cold weather operation
When operating tools at temperatures below freezing:
Keep the tool as warm as possible before use.
Disconnect the airline from the tool.
Put 5-10 drops of DEWALT pneumatic tool oil (or
winter-weight pneumatic oil containing ethylene
glycol) into the air inlet.
Set the air pressure to a maximum of 5.5 bar.
Connect the air hose to the fitting on the tool.
Load nails into the magazine as described below.
Actuate the tool 5 or 6 times into scrap lumber to
lubricate the o-rings.
Increase the air pressure to the normal operating
level.
Use the tool in the normal manner.
Hot weather operation
The tool should operate normally. Avoid the heat of
direct sunlight to avoid damage to the bumpers,
o-rings, and other rubber parts.
Loading the tool (fig. C)
These tools are equipped with a dual-load
magazine.
Always connect the tool to the air supply
before loading nails.
Select an appropriate collated nail stick. See
“Technical data”.
Load the magazine using one of the following
methods:
Loading and locking
Insert collated nail stick (s) into the loading slot in
the rear of the magazine.
Pull the nail pusher (11) rearward to fall behind
the nails.
Locking and loading
Lock the nail pusher (11) in the back position.
Insert collated nail stick (s) into the loading slot in
the rear of the magazine.
Unlatch the nail pusher by pushing forward and
carefully slide the nail pusher forward to press
against the nails.
Actuating the tool (fig. D)
These tools are equipped with a trigger/lock-off
switch (1). When rotated to the right, this switch
prevents the tool from actuating.
When the switch is centred, the tool will be fully
operational. The tool can be operated using one of
two modes: sequential action mode or bump action
mode. The trigger installed on the tool determines
the mode of actuation.
Sequential action mode
The sequential action mode is used for intermittent
nailing when very careful and accurate placement is
desired.
Fit the grey trigger as described above.
Push the contact trip against the work surface.
Pull the trigger to actuate the tool. Each trigger
pull with the contact trip pushed against the work
surface will drive one nail.
Bump action
The bump action mode is used for rapid nailing on
flat, stationary surfaces.
Fit the black trigger as described above.
To drive a single nail: Operate the tool as
described for sequential action.
D51256.P65 28-12-2001, 09:2123
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D51275K T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D51275K T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info