546215
19
Zoom out
Zoom in
Previous page
1/26
Next page
17
ENGLISH
For use in all modes:
A10
44 Three way dust extraction kit (D271054)
A11
144 Laser
INTENDED USE
Your D
EWALT D27105 flip-over saw has been designed to operate as a
mitre saw or a saw bench to perform the four main sawing operations of
ripping, cross-cutting, bevelling and mitring easily, accurately and safely.
This unit is designed for use with a nominal blade diameter 305 mm carbide
tip blade for professional cutting wood, wood products and plastics.
DO NOT use under wet conditions or in presence of flammable liquids or
gases.
These flip over saws are professional power tools.
DO NOT let children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
WARNING! Do not use the machine for purposes other than
intended.
Mitre saw mode
In mitre saw mode, the sawing machine is used in vertical, mitre or bevel
position.
Saw bench mode
Turned over on its central axis, the sawing machine is used to perform
the standard ripping operation and for sawing wide pieces by manually
feeding the workpiece into the blade.
Electrical Safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your tool is double insulated in accordance with EN 61029;
therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the primary
and secondary winding.
In case of cord replacement the tool must only be repaired by an authorized
service agent or by qualified electrician.
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
The plug fitted should be comply with BS EN 60309 (BS4343),
16 Amps, earthing contact position 4h.
WARNING: Always ensure that the cable clamp is correctly and
securely fitted to the sheath of the cable.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable
suitable for the power input of this tool (see technical data).
The minimum conductor size is 1.5 mm
2
. When using a cable reel, always
unwind the cable completely.
ASSEMBLY
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
Unpacking the machine and its parts.
WARNING: To reduce the risk of injury, always seek assistance
when moving the machine.
Remove the loose packaging material from the box.
Lift the machine out of the box.
Remove the parts box from the interior of the machine.
Remove any remaining packing material from the machine.
Mounting the feet (fi g. B, B1)
With the feet and legs mounted, alternatively the machine is suitable for
placement on a workbench. To ensure a safe operation, the machine must
be fastened to the workbench.
WARNING! Do never operate this machine when it is not
fastened to the workbench. The feed force will make the saw
unstable if not fastened to the workbench.
Turn the machine upside down
Place a foot (16) on each of the mounting locations (51) on the base
Slide a nut (52) into the slots (53) located above the mounting locations
Insert a bolt (54) fitted with a washer (55) into the feet
Tighten the bolts
Mount the legs as described below.
Fold the legs as described below
Turn the machine straight up
Insert a bolt of 8 mm and 120 mm minimum length (49) into the feet on
each mounting location (fig. B1).
Tighten the bolts
Mounting the legs (fi g. C1 & C2)
With the legs mounted, the machine is suitable for stand-alone placement.
Turn the machine upside down.
Mount the legs as described below. Beware that the front legs and the
rear legs have different lengths. The rear legs are slightly longer than
the front legs. Make sure to mount the legs in the correct place.
Turn the machine straight up. Make sure it is level; adjust the leg
clamping height if required.
Rear legs
Present a leg (15) to each of the mounting points (56) located at the
lower edges on the inside of the base (fi g. C1).
Pass a coach bolt (57) from the outside through the holes into the
frame and the legs.
Place a bracket (58) and a lock knob (59) onto the bolts.
Tighten the lock knobs.
Front legs
Present a leg (15) to each of the mounting points (56) located at the
upper edges on the inside of the base (fi g. C2).
Place a bracket (58) over the legs.
Pass a coach bolt (57) from the inside through the holes into the
brackets, the legs and frame.
Place a lock knob (59) onto the bolts.
Tighten the lock knobs.
Folding the legs (fi g. C3)
The legs can be folded into the base to make the machine suitable for use
on a workbench.
Turn the machine upside down.
Loosen the lock knob (59) of the fi rst leg (15).
Fold the leg inwards.
Tighten the lock knob.
Repeat as for the other legs.
Turn the machine straight up.
Mounting the wheels (fi g. D)
Place a wheel (14) onto the axles (60) on each side of the machine.
Place a fl at washer (61) and a nut (62) onto the threaded end of the axles.
Tighten the nuts using the spanner supplied.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D27105 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D27105 T 3 in the language / languages: English as an attachment in your email.

The manual is 7,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info