Manual DeWalt D25840K (page 29 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

544669

Zoom out

Zoom in

1/120

ENGLISH

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 2)

Turn the dial (b) to the desired level. Turn the dial

upwards for higher speed and downwards for

lower speed. The required setting is a matter of

experience, e. g.:

– when chiselling or drilling in soft, brittle materials

or when minimum break-out is required, set the

dial to a low setting;

– when breaking or drilling in harder materials, set

the dial to a high setting.

Assembling and Fitting the Side

Handle (ﬁ g. 7)

The side handle (h) can be mounted on either side of

the machine to suit both RH- and LH-users.

WARNING: Always operate the

tool with the side handle properly

assembled.

1. Snap the steel ring (j) over the collar (g) behind

the tool holder (f).

2. Place the clamping pieces (k) over the ends of

the steel ring.

3. Fit the locking plates (l) into the side handle (h).

4. Squeeze the clamping pieces together and fit

the side handle, making sure that the teeth on

the locking plates (l) and the clamping pieces (k)

engage.

5. Insert the bolt (m) and screw on the clamp

wheel (n). Do not tighten.

6. Move the side handle mounting assembly to the

desired position.

7. Lock the side handle mounting assembly in

place by tightening the clamp wheel (n).

OPERATION

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• For your own safety, always use the

tool with both hands.

• Be aware of the location of pipework

and wiring.

• Apply a pressure of approx. 20 kg

to the tool. Excessive force does not

speed up chiselling but decreases tool

performance and may shorten tool life.

Proper Hand Position (ﬁ g. 1, 8)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (h), with the other hand on the main handle

(i).

Switching On and Off (ﬁ g. 9)

1. To turn the tool on, press the lower part of the

on/off switch (a).

2. To turn the tool off, press the upper part of the

on/off switch (a).

Chipping and Chiselling (ﬁ g. 1)

1. Insert the appropriate chisel and rotate it by

hand to lock it into one of 24 positions.

2. Set the electronic speed and impact control dial

(b).

3. Fit and adjust the side handle (h).

4. Switch on the tool and start working.

5. Always turn the tool off when work is finished

and before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Service Indicator LEDs (ﬁ g. 2)

The yellow brushwear indicator LED (d) lights up

when the carbon brushes are nearly worn out.

After a further 8 hours of use, the brushes have

completely worn out and the motor will automatically

be shut off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25840K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25840K Manual

Product: