Manual DeWalt D25840K (page 28 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

544669

Zoom out

Zoom in

1/120

ENGLISH

– minimised break-out when chiselling soft or

brittle materials

– optimal tool control for precise chiselling

Service Indicator LEDs (ﬁ g. 2)

The yellow brushwear indicator LED (d) lights up

when the carbon brushes are nearly worn out to

indicate that the tool needs servicing within the next

8 hours of use. The red service indicator LED (c)

lights up if there is a fault with the tool or the brushes

have completely worn out.

Fully Vibration-dampened Main

Handle

The dampers in the main handle (i) absorb the

vibrations transmitted to the user. This improves user

comfort during the operation.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data).

The minimum conductor size is 1.5 mm

. When

using a cable reel, always unwind the cable

completely.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Inserting and Removing SDS Max

Accessories (ﬁ g. 3, 4)

This machine uses SDS Max

drill bits and chisels

(refer to the inset in figure 4 for a cross-section of an

SDS Max

bit shank).

1. Clean and grease the bit shank. Only apply a

slight amount of lubricant to the bit shank. Do

not apply lubricant to the machine.

2. Insert the bit shank into the tool holder (f), and

press and turn the bit slightly until the sleeve

snaps into position.

3. Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

4. To remove a bit pull back the tool holder locking

sleeve (f) and pull the bit out of the tool holder.

Indexing the Chisel Position (ﬁ g. 5, 6)

The chisel can be indexed and locked into 24

different positions (fig. 6).

1. Rotate the mode selector switch (e) until it

points towards the 0 position.

2. Rotate the chisel in the desired position.

3. Set the mode selector switch (e) to the

hammering only position.

4. Twist the chisel until it locks in position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25840K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25840K Manual

Product: