723581

DeWalt D25651 Manual

10
Zoom out
Zoom in
Previous page
1/36
Next page
ENGLISH
8
if the lock-on slider is activated when changing from chisel
mode into hammerdrillingmode.
D25831, D25851
For continuous operation, move the toggle switch1 to the
on position. To stop continuous operation, move the toggle
switch to the offposition.
Soft Start Feature
The soft start feature allows you to build up speed slowly,
thus preventing the drill bit from walking off the intended
hole position when starting. The soft start feature also
reduces the immediate torque reaction transmitted to the
gearing and the operator if the hammer is started with the
drill bit in an existinghole.
Hammerdrilling with a Solid Bit (Fig. A, E)
D25501, D25553, D25601, D25603,
D25651
NOTE: The D25831 and D25851 have only chipping modes
with no hammerdrillingcapability.
1. Set the mode selector6 to hammerdrillingmode.
2. For D25603 and D25651 only, move the torque control
lever 8  to Setting 1 14 .
3. Set the speed and impact control dial7.
4. Insert the appropriate drillbit.
5. Adjust the side handle (front or rear position)3.
6. Mark the spot where the hole is to bedrilled.
7. Place the drill bit on that mark and depress the trigger
switch1.
8. Apply only enough pressure to engage active
vibration control (refer to SHOCKS Active Vibration
Control®System).
9. To stop the tool, release the trigger switch.
Always turn the tool off when work is finished and
beforeunplugging.
Hammerdrilling with a Core Bit (Fig. A, E)
D25501, D25553, D25601, D25603,
D25651
CAUTION: Do not use a core bit for hammerdrilling
wood. Personal injury and damage to tool mayresult.
NOTE: The D25831, D25851 have only chipping modes with
no hammerdrillingcapability.
1. Set the mode selector6 to hammerdrillingmode.
2. For D25603 and D25651 only, move the torque control
lever 8  to Setting 2 11 .
3. Turn the speed and impact control dial7 to the
desiredspeed.
4. Adjust the side handle (front or rear position)3.
5. Assemble the centering bit and adapter shank into
corebit.
6. Mark the spot where the hole is to bedrilled.
7. Place the centering bit on that mark and depress the
trigger switch1.
NOTE: Some core drills require the removal of centering
bit after about 1 cm of penetration. If so, remove and
continuehammerdrilling.
8. When hammerdrilling through a structure thicker than
the depth of the core bit, break away the round cylinder
of concrete or core inside the bit at regular intervals. To
avoid unwanted breaking away of concrete around the
hole, first drill a hole the diameter of the centering bit
completely through the structure. Then drill the cored
hole halfway from each side of thestructure.
9. To stop the tool, release the trigger switch.
Always turn the tool off when work is finished and
beforeunplugging.
Chipping and Chiseling (Fig. A)
D25831, D25851
1. Set the mode selector6 to chippingmode.
2. Set the impact control dial7 to desired setting (refer to
Electronic Speed and ImpactControl).
3. Insert the appropriate chisel and rotate it by hand to
lock it into the desiredposition.
NOTE: For SDS Max models, only use SDS Maxbits.
4. Adjust the side handle (front or rear position)3.
5. Depress the trigger switch1.
6. Apply only enough pressure to engage active
vibration control (refer to SHOCKS Active Vibration
Control®System).
7. To stop the tool, release the trigger switch.
Always turn the tool off when work is finished and
beforeunplugging.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthis.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt D25651 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25651 in the language / languages: English, French, Spanish, All languages as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info