Manual DeWalt D25601K (page 36 of 160) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544648

Zoom out

Zoom in

1/160

ENGLISH

4. Slide and rotate the side handle to the desired

position.

5. Lock the side handle in place by tightening the

knob (p).

Inserting and Removing SDS Max

Accessories (ﬁ g. 1, 4A, 4B)

This machine uses SDS Max

bits and chisels (refer

to the inset in figure 4B for a cross-section of an

SDS Max

bit shank).

1. Clean the bit shank.

2. Pull back the locking sleeve (m) and insert the

bit shank.

3. Turn the bit slightly until the sleeve snaps into

position.

4. Pull on the bit, to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

5. To remove a bit pull back the tool holder locking

sleeve/collar (m) and pull the bit out of the tool

holder (l).

Selecting the Operating Mode

(ﬁ g. 1)

Hammerdrilling:

D25501, D25601, D25602, D25603

for concrete, brick, stone and masonry

drilling operations.

Hammering only:

D25501, D25601, D25602, D25603,

D25820, D25831

for chiselling and demolition applications.

In this mode the tool can also be used as

a lever to free a jammed drill bit.

1. To select the operating mode, rotate the mode

selector switch (f) until it points to the symbol of

the required mode.

It may be neccessary to twist the tool holder (l)

slightly to allow the mode selector switch (f) to

pass the position.

2. Check that the mode selector switch (f) is

locked in place.

Indexing the Chisel Position

(ﬁ g. 5)

D25501, D25601, D25602, D25603, D25820, D25831

The chisel can be indexed and locked into 18

different positions.

1. Rotate the mode selector switch (f) until it points

towards the

position.

2. Rotate the chisel in the desired position.

3. Set the mode selector switch (f) to the

“hammering only” position.

4. Twist the chisel until it locks in position.

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 1, 3)

D25601, D25602, D25603, D25831

Turn the dial (g) to the desired level. Turn the dial

upwards for higher speed and downwards for

lower speed. The required setting is a matter of

experience, e.g.

– when chiselling or drilling in soft, brittle materials

or when minimum break-out is required, set the

dial to a low setting;

– when breaking or drilling in harder materials, set

the dial to a high setting.

Setting the Two Stage Mechanical

Clutch (ﬁ g. 3)

D25602, D25603

NOTICE: Always turn the tool off before

changing torque control settings or

damage to the tool may result.

Move the torque control lever (u) to setting 40Nm or

80Nm as needed for application.

• Clutch Setting 40Nm (s) is designed for most

drilling applications and is designed to easily

clutch out when the drill bit encounters re-bar or

other foreign substances.

• Clutch Setting 80Nm (t) is designed for higher

torque applications such as core-bits and deep

hole drilling and is designed to clutch out at a

higher torque threshold.

NOTE: If it is not possible to select position 80Nm,

run the unit under load and try again.

Each time the tool is plugged in, it will automatically

default to clutch setting 1 into clutch setting 40Nm

(s), the most sensitive setting.

Depth Rod

(ADDITIONAL ACCESSORY)

1. Push in and hold the depth rod release button

on the side handle.

2. Move the depth rod so the distance between

the end of the rod and the end of the bit equals

the desired drilling depth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D25601K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D25601K Manual

Product: