388889

DeWalt d 25313 k Manual

30
Zoom out
Zoom in
Previous page
1/120
Next page
30
E N G L I S H
Hammer drilling (fig. A)
Drilling with a solid bit
● Set the mode selector switch (3) to the
"hammer drilling" position.
● Insert the appropriate drill bit. For best results
use high quality carbide-tipped bits.
● Adjust the side handle (9) as required.
● If necessary, set the drilling depth.
● Mark the spot where the hole is to be drilled.
● Place the drill bit on the spot and switch on the
tool.
● Always switch off the tool when work is finished
and before unplugging.
Drilling with a core bit
● Set the mode selector (3) to the "hammer
drilling" position.
● Adjust the side handle (9) as required.
● Insert the appropriate core bit.
● Assemble the centerdrill into the core bit.
● Place the centerdrill on the spot and press the
variable speed switch (1). Drill until the core
penetrates into the concrete approx. 1 cm.
● Stop drilling and remove the centerdrill. Place the
core bit back into the hole and continue drilling.
● When drilling through a structure thicker than
the depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a
hole the diameter of the centerdrill completely
through the structure. Then drill the cored hole
halfway from each side.
● Always switch off the tool when work is finished
and before unplugging.
Rotary drilling (fig. A)
● Set the mode selector switch (3) to the "rotary
drilling" position.
● Depending on your tool, follow either of the
following instructions:
- Fit the chuck adapter/chuck assembly
(D25313K).
- Replace the tool holder with the chuck
(D25314K).
● Proceed as described for hammer drilling.
@
Never use standard chucks in the
hammer drilling mode.
Screwdriving (fig. A)
● Set the mode selector switch (3) to the "rotary
drilling" position.
● Select the direction of rotation.
● Depending on your tool, follow either of the
following instructions:
- Insert the special SDS-plus® screwdriving
adaptor for use with hexagonal screwdriver
bits (D25313K).
- Replace the tool holder with the chuck
(D25314K).
● Insert the appropriate screwdriver bit. When
driving slotted head screws always use bits with
a finder sleeve.
● Gently press the variable speed switch (1) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
● When the screw is flush with the workpiece,
release the variable speed switch to prevent the
screw head from penetrating into the workpiece.
Chipping and chiselling (fig. A)
● Set the mode selector switch (3) to the
"hammering only" position.
● Insert the appropriate chisel and rotate it by
hand to lock it into one of 51 positions.
● Adjust the side handle (9) as required.
● Switch on the tool and start working.
● Always switch off the tool when work is finished
and before unplugging.
&
● Do not use this tool to mix or pump
easily combustible or explosive fluids
(benzine, alcohol, etc.).
● Do not mix or stir inflammable liquids
labelled accordingly.
Optional accessories
Various types of SDS-plus
®
drill bits and chisels
are available as an option.
Consult your dealer for further information on the
appropriate accessories.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt d 25313 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt d 25313 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info