388889

DeWalt d 25313 k Manual

28
Zoom out
Zoom in
Previous page
1/120
Next page
28
E N G L I S H
For 115 V units with a power rating exceeding
1500 W, we recommend to fit a plug to BS4343
standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
machine (see technical data). The minimum
conductor size is 1.5 mm
2
.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
@
Prior to assembly and adjustment
always unplug the tool.
Selecting the operating mode (fig. B)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling operations.
Hammering only: for light chipping,
chiselling and demolition applications.
In this mode the tool can also be used
as a lever to free a jammed drill bit.
Bit rotation: non-working position used
only to rotate a flat chisel into the
desired position.
● To select the operating mode, press the safety
lock (4) and rotate the mode selector switch (3)
until it points to the symbol of the required mode.
● Release the safety lock and check that the
mode selector switch is locked in place.
@
Do not select the operating mode when
the tool is running.
Indexing the chisel position
The chisel can be indexed and locked into
51 different positions.
● Rotate the mode selector switch (3) until it
points to the "bit rotation" position.
● Rotate the chisel in the desired position.
● Set the mode selector switch (3) to the
"hammering only" position.
● Twist the chisel until it locks in position.
Inserting and removing SDS-plus
®
accessories
(fig. C)
This tool uses SDS-plus
®
accessories (refer to the
inset in fig. C for a cross-section of an SDS-plus
®
bit shank).
We recommend to use professional accessories only.
● Clean and grease the bit shank.
● Insert the bit shank into the tool holder (5).
● Push the bit down and turn it slightly until it fits
into the slots.
● Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
● To remove a bit pull back the tool holder locking
sleeve (11) and pull out the bit.
@
Always wear gloves when you change
accessories. The exposed metal parts
on the tool and accessory may become
extremly hot during operation.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt d 25313 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt d 25313 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info