388887

DeWalt d 25113 k qs Manual

34
Zoom out
Zoom in
Previous page
1/140
Next page
34
E N G L I S H
Instructions for use
@
● Always observe the safety instructions
and applicable regulations.
● Be aware of the location of pipework
and wiring.
● Apply only a gentle pressure to the tool
(approx. 5 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
● Do not drill or drive too deep to prevent
damage to the dust cover.
● Always hold the tool firmly with both
hands and ensure a secure stance
(fig. H). Always operate the tool with the
side handle properly mounted.
Switching on and off (fig. A)
D25112(C)K/D25113K/D25114K
● To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
● For continuous operation, press and hold down
the variable speed switch, press the lock-on
button (2) and release the switch.
● To stop the tool, release the switch.
● To stop the tool in continuous operation, press
the switch briefly and release it. Always switch
off the tool when work is finished and before
unplugging.
D25213K
● To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
● To stop the tool, release the switch.
● To lock the tool in off position, move the
forward/reverse slider (3) to the central position.
Hammer drilling (fig. A)
Drilling with a solid bit
● Set the mode selector switch (4) to the
"hammer drilling" position.
● Insert the appropriate drill bit. For best results
use high quality carbide-tipped bits.
● Adjust the side handle (9) as required.
● If necessary, set the drilling depth.
● Mark the spot where the hole is to be drilled.
● Place the drill bit on the spot and switch on the
tool.
● Always switch off the tool when work is finished
and before unplugging.
Drilling with a core bit
● Set the mode selector (4) to the "hammer
drilling" position.
● Adjust the side handle (9) as required.
● Insert the appropriate core bit.
● Assemble the centerdrill into the core bit.
● Place the centerdrill on the spot and press the
variable speed switch (1). Drill until the core
penetrates into the concrete approx. 1 cm.
● Stop drilling and remove the centerdrill.
Place the core bit back into the hole and
continue drilling.
● When drilling through a structure thicker than
the depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a
hole the diameter of the centerdrill completely
through the structure. Then drill the cored hole
halfway from each side.
● Always switch off the tool when work is finished
and before unplugging.
Rotary drilling (fig. A)
● Set the mode selector switch (4) to the "rotary
drilling" position.
● Depending on your tool, follow either of the
following instructions:
- Fit the chuck adapter/chuck assembly
(D25112(C)K/D25113K/D25213K).
- Replace the tool holder with the chuck
(D25114K).
● Proceed as described for hammer drilling.
@
Never use standard chucks in the
hammer drilling mode.
Screwdriving (fig. A)
● Set the mode selector switch (4) to the
"rotary drilling" position.
● Select the direction of rotation.
● Depending on your tool, follow either of the
following instructions:
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt d 25113 k qs at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt d 25113 k qs in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info