388887

DeWalt d 25113 k qs Manual

33
Zoom out
Zoom in
Previous page
1/140
Next page
33
E N G L I S H
● Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
● To remove a bit pull back the tool holder locking
sleeve (12) and pull out the bit.
@
Always wear gloves when you change
accessories. The exposed metal parts
on the tool and accessory may become
extremly hot during operation.
Fitting the side handle (fig. D)
The side handle (10) can be fitted to suit both
RH- and LH-users.
@
Do not use the tool without the side
handle properly assembled.
● Loosen the side handle.
● For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
● For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
● Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
● Insert the required drill bit as described above.
● Press the depth stop clamp (11) and keep it
depressed.
● Fit the depth adjustment rod (9) through the
hole in the depth stop clamp.
● Adjust the drilling depth as shown.
● Release the depth stop clamp.
Forward/reverse slider (fig. F1 & F2)
D25112(C)K/D25113K/D25114K (fig. F1)
● Push the forward/reverse slider (3) to the
RH-side for forward (RH) rotation. See arrows
on tool.
● Push the forward/reverse slider (3) to the
LH-side for reverse (LH) rotation.
D25213K (fig. F2)
● Push the forward/reverse slider (3) to the
LH-side for forward (RH) rotation. See arrows
on tool.
● Push the forward/reverse slider (3) to the
RH-side for reverse (LH) rotation.
@
Always wait until the motor has come to
a complete standstill before changing
the direction of rotation.
D25112(C)K/D25113K/D25213K -
Fitting the chuck adapter & chuck
● Screw the chuck onto the threaded end of the
chuck adapter.
● Insert the connected chuck and adapter in the
tool as though it were a standard SDS-plus® bit.
● To remove the chuck, proceed as for removing
a standard SDS-plus® bit.
@
Never use standard chucks in the
hammer drilling mode.
D25114K - Replacing the tool holder with the
chuck (fig. G)
● Turn the locking collar (8) into the unlocking
position and pull the tool holder (6) off.
● Push the chuck (13) onto the spindle and turn
the locking collar into the locking position.
● To replace the chuck with the tool holder, first
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
@
Never use standard chucks in the
hammer drilling mode.
Replacing the dust cover (fig. C)
The dust cover (7) prevents dust ingress into
the mechanism. Replace a worn dust cover
immediately.
● Pull back the tool holder locking sleeve (12) and
pull the dust cover (7) off.
● Fit the new dust cover.
● Release the tool holder locking sleeve.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt d 25113 k qs at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt d 25113 k qs in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info