Manual DeWalt D 23550 (page 35 of 140) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

110214

Zoom out

Zoom in

1/140

ENGLISH

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Depth of Cut Adjustment (ﬁ g. 1–3)

1. Loosen the depth adjustment knob (n).

2. Move the shoe (f) to obtain the correct depth of

cut.

3. Tighten the depth adjustment knob (n).

WARNING: For optimal results, allow

the saw blade to protrude from the

workpiece by about 3 mm (see inset in

figure 3).

Bevel Adjustment (ﬁ g. 4)

The bevel angle can be adjusted between 0° and

45° for the D23550 and between 0° and 55° for the

D23650.

1. Loosen the bevel adjustment knob (k).

2. Set the bevel angle by tilting the saw shoe (f)

until the mark indicates the desired angle on the

scale.

3. Tighten the bevel adjustment knob (k).

Shoe Adjustment for 90° Cuts

(ﬁ g. 1, 5)

1. Adjust the saw to 0° bevel.

2. Retract the blade guard using the lever (h) and

place the saw on the blade side.

3. Loosen the bevel adjustment knob (k).

4. Place a square against the blade and shoe to

adjust the 90° setting.

5. Adjust the stop (o) as required.

Replacing the Saw Blade (ﬁ g. 6)

1. Engage the blade lock button (d) and unscrew

the blade clamping screw (q) by turning

counterclockwise using the spanner (r) supplied

with the tool.

2. Retract the lower blade guard (i) using the

lever (h) and replace the blade (j). Reinstall the

washers (s, t) in the correct position.

3. Check the direction of rotation of the blade.

4. Thread on the blade clamping screw (q) by

hand to hold the washer in position. Turn

clockwise.

5. Press the blade lock button (d) while turning the

spindle until the blade stops rotating.

6. Tighten the blade clamping screw firmly using

the spanner.

Adjusting the Riving Knife (ﬁ g. 6)

For the correct adjustment of the riving knife (g),

refer to the inset in figure 6. Adjust the clearance

of the riving knife after changing the saw blade or

whenever necessary.

1. Adjust the depth of cut to 0 mm to access the

clamping screws of the riving knife.

2. Loosen the screws (u) and pull out the riving

knife to its maximum length.

3. Adjust the clearance and tighten the screws

(torque: 4–5 Nm).

Mounting and Adjusting the Parallel

Fence (ﬁ g. 7)

The parallel fence (o) is used for cutting parallel to

the edge of the workpiece.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt D 23550 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt D 23550 Manual

Product: