674266
5
Zoom out
Zoom in
Previous page
1/14
Next page
position.
It is recommended to format the SD-card by the camera when used at the first time.
The camera will be in USB mode when connected to a USB port of a computer. In this
case, the SD-card functions as a removable disk.
Please ensure sufficient power when having firmware upgrade, otherwise the upgrade
process could be interrupted incorrectly. If any fault occurs after improper upgrading
process, the camera may stop function properly.
3.Easy Operation
3.1 Power Supply
To supply power for the camera, 4 or 8 AA size batteries are needed.
Confirm that the power switch is at the OFF (Right) position, take out the battery depot.
Load the fully charged batteries into the depot according the polarities sign shown
below. Push back the battery compartment to the battery chamber.
The following batteries with 1.5V output can be used:
1. High-density and high-performance alkaline batteries (Recommended)
2. Rechargeable NiMH batteries
There are four battery slots. When in Test Mode, camera will be automatically shut
down to save power if without any operation within 3 minutes; it could be waked up by
any movement detection.
When in low-battery state, camera will be also automatically shut down. Please change
the batteries in time.
3.2
Insert the Micro SD-card
Insert Micro SD-card into the card slot with marked side upwards.
Please note that the Micro SD-card can only be plugged in one direction. Power on and
3.2.1 Enter into the ON Mode
Before switching on, please pay attention to the following:
1. Avoid temperature and motion disturbances that could be construed as animals
or humans such as trees that are exposed to direct sunlight for much of the day
ENG-5
5


Need help? Post your question in this forum.

Forumrules
1

Forum

denver-wct-8010

Reset search

  • I have put a 128 GB card in the slot and I get the information ´ard error´. What can I do ? It did not read anywhere in the manual about specification of a card... Submitted on 29-3-2020 at 12:18

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denver WCT-8010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denver WCT-8010 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denver WCT-8010

Denver WCT-8010 User Manual - German - 14 pages

Denver WCT-8010 Quick start guide - Dutch - 2 pages

Denver WCT-8010 Quick start guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info