695741

Denver MRP-161 Manual

27
Zoom out
Zoom in
Previous page
1/73
Next page
EN-2
3. The LCD display (2) will display the first & second digit of “ 00 ” is flashing. Press skip up or skip down button (25,12) to
set the correct hour. Press “ Mem/Clk-adj ” button (14) to store the correct hour.
4. The third & fourth digit of “ 00 ” is flashing, press the skip up or skip down button (25,12) to set the correct minutes.
Then press “ Mem/Clk-adj ” button (14) to store the correct minute.
Listening to radio
Manual tuning
1. Tune on the unit by press power On/Standby button (7)
2. Press Function button (10) to select “ Tuner ” mode.
3. Tune to the required station by pressing the skip up or skip down button (25,12).
4. Adjust volume up/down button (14) to the desired volume level.
Auto tuning
1. Press Function button (10) to select “ Tuner ” mode.
2. Press and hold the skip up/down button (25,12) for 1-2 seconds and then release.
3. The unit will start seeking automatically and stop until a radio station is reached.
4. Repeat step 2 until the desired radio station is being reached.
5. Adjust volume up/down button (3) to the desired volume level.
Preset stations
You can store up to 10 radio stations in the memory (10 FM).
1. Set to tuner mode.
2. Turn to the desired radio station by “ manual” or “ auto ” tuning method.
3. Press “ Mem/Clk-adj ” button (14) to enable program function & “ MEM ” icon and preset station nr will flash on LCD display (2)
4. Press “ Pre-up or Pre-dn ” button (26,13) to select the desired station memory for storage.
5. Press “ Mem/Clk-adj ” button (14) again to confirm the setting.
6. Repeat step 2 to 5 to store other stations.
7. Now you can select the presets stations in order by pressing the “Pre–up ” button (26) or Pre-dn button (13).
The pre-set memories will be cancelled completely if dis-connecting the main power supply. You are recommended to
switch the system into standby mode for convenience usage.
There are 10 seconds for program state, after 10 sec. This state would resume to normal tuner mode automatically.
You can overwrite a present station by storing another frequency in its place.
FM & FM-stereo reception
Press the “ St/Mono ” button (8) repeatedly, the FM programs are receiving in mono and stereo mode repeatedly. In particular
when stereo signals are weak. It is preferable to receive the program in mono.
If stereo signal is being received, the stereo indicator “ ” will appear on LCD display (2) to show FM stereo program is now
receiving.
Hints for best reception:-
- FM : the receiver has a build-in FM wire antenna (34) hanging at the back of the unit. This wire should be totally unraveled and
extended for the best reception.
Phono
noted:
- Remove the stylus protector.
- Be sure that the tone arm is being detached from the tone arm rest before operating and re-secured again afterwards.
Press Function button (10) to select “ Phono ” mode.
1. Set the speed selector (30) to the proper position depending on the type of record to be played.
2. Place the record on the platter (use the spindle adaptor (29) if required).
3. Lift the tone arm from the pick up holder (31) and slowly move it to the record side. The platter will
start to rotate.
4. Place the tone arm to the desired position of the record.
5. Adjust the Volume up/down button (3) to the desired level.
6. At the end of record, the platter will automatically stop rotating. Lift the tone arm from the record and
return it to the rest position (31).
7. To stop intermediate, lift up the tone arm from the record and return it to the rest (31).
Remark : As some kind of record the auto-stop area was out of the unit setting, so it will stop before the last
track finish. In this case, select the auto-stop switch (33) to “ off ”position, then it will run to the end of the
record but will not stop automatically (turn off the unit by power button or switch back the auto-stop switch (33)
to “ on ” position to stop the platter rotate). Then put back the tone arm to the rest position (31).
Playing compact disc
Getting start
1. Press Function button (10) to select “ CD ” mode.
2. Press “ Open/Close ” button (24) to open the CD tray (17).
3. Place a CD with the printed side facing up inside the tray & then close the CD tray.
4. Focus search is performing, then will start the playback automatically.
Play / pause mode
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denver MRP-161 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denver MRP-161 in the language / languages: All languages as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denver MRP-161

Denver MRP-161 User Manual - Dutch - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info