498669
10
Zoom out
Zoom in
Previous page
1/98
Next page
ENGLISH
Simple
Version
Remote
Control
Playback
(Advanced)
Connections
Playback
(Basic)
Multi-
zone
GUISettings
Getting
Started
Troubleshooting
Other
Information
Spec. Index
Part
Names
1
Prepare the Setup
Microphone
Mount the setup microphone on a
tripod or stand and place it in the
main listening position.
When placing the setup microphone, adjust
the height of the sound receptor part to the
level of the listener’s ear.
Sound receptor
Setup
microphone
NOTE
Do not hold the setup microphone in your hand
during measurements.
Avoid placing the setup microphone close to a
seat back or wall as sound reflections may give
inaccurate results.
NOTE
Make the room as quiet as possible. Background noise can disrupt the room
measurements. Close windows, silence cell phones, televisions, radios, air
conditioners, fluorescent lights, home appliances, light dimmers, or other
devices as measurements may be affected by these sounds.
Cell phones should be placed away from all audio electronics during the
measurement process as Radio Frequency Interference (RFI) may cause
measurement disruptions (even if the cell phone is not in use).
Do not unplug the setup microphone from the main unit until Audyssey Auto
Setup is completed.
Do not stand between the speakers and setup microphone or allow obstacles
in the path while the measurements are being made. This will cause inaccurate
readings.
Loud test sounds may be played during Audyssey
MultEQ automatic speaker setup. This is part of normal
operation. If there is background noise in room, these
test signals will increase in volume.
Operating VOLUME during the measurements will cancel
the measurements.
Measurement cannot be performed when headphones
are connected.
Front
If the result differs from the actual connection status, or if “Caution!” is
displayed, see “Error Messages” (vpage 9). Then carry out Audyssey Auto
Setup again.
If the result still differs from the actual connection status after remeasurement
or the error message still appears, it is possible that the speakers are not
connected properly. Turn this unit off, check the speaker connections and
repeat the measurement process from the beginning.
If you change a speaker position or orientation, perform Audyssey Auto Setup
again to obtain optimal equalizer correction.
About Setup Microphone Placement
Measurements are performed by placing the setup microphone successively
at multiple positions throughout the entire listening area, as shown in
GExample qH. For best results, we recommend you measure in six positions,
as shown in the illustration (up to six positions).
Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment results in
more effective correction.
FL SW C FR
SRSL
*
M
FL SW C FR
SRSL
*
M
(
: Measuring positions)
GExample qH GExample wH
(
: Measuring positions)
FL Front speaker (L) SW Subwoofer
FR Front speaker (R) SL Surround speaker (L)
C Center speaker SR Surround speaker (R)
About the Main Listening Position (*M)
The main listening position is the position where listeners would normally
sit or where one would normally sit alone within the listening environment.
Audyssey MultEQ uses the measurements from this position to calculate
speaker distance, level, polarity, and the optimum crossover value for the
subwoofer.
n
Set Up Speakers (Audyssey™ Auto Setup)
1 2 4 53
The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made
automatically. This is called “Audyssey Auto Setup”.
To perform measurement, place the setup microphone in multiple locations all around the listening area. For best results, we recommend
you measure in six positions, as shown in the illustration (up to six positions).
When performing Audyssey Auto Setup, MultEQ
®
/Dynamic EQ™/Dynamic Volume™ functions become active (vpage 53).
To set up the speakers manually, use “Manual Setup” – “Speaker Setup” (vpage 55) on the GUI menu.
44
The “Simple Version” describes the installation, connection and setup methods for 5.1-channel speakers.
See page 36 for the installation, connection and setup methods for speakers other than 5.1-channel speakers.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon S-5BD - Cara at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon S-5BD - Cara in the language / languages: English as an attachment in your email.

The manual is 17,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon S-5BD - Cara

Denon S-5BD - Cara User Manual - German - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info