584591
12
Zoom out
Zoom in
Previous page
1/18
Next page
Settings and Connections
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
w q w q
"6%*0
065
13&13&
065
NOTE
The same signal is output to speakers A and B.
Please use the following speaker impedance.
· When using only speaker A or B ····························· 4 ~ 16 Ω/ohms
· When using speakers A and B at the same time ····8 ~ 16 Ω/ohms
Normal Connections
Example: Normal connection to the
channel
b Setup each channel (
~ ,
~ ) using the same steps.
Connection for signal input to each channel to be output from the channel’s speaker terminal.
Set each switch as shown below.
q Set the Operation mode select switch to “NORMAL” (vpage 6).
w Set the Input select switch according to the input (vpage 6).
· For RCA input ······ Set to “RCA”.
· For XLR input ······· Set to “XLR”.
Set the rear panel “Operation mode select switch” and “Input select switch” according to the
connection method.
NOTE
The Operation mode select switch and Input select switch must be set before turning the power on.
Settings which are changed after powering on will not be registered. In such cases, the power should be
switched off and on again.
SPEAKER ASPEAKER B
Input select switch Operation mode select switch
Bi-wiring connection
When using speakers that have input terminals for both woofer units and tweeter units, this connection
allows for the same signal to be output from each unit.
With this connection the interference between signals for the woofer unit and tweeter unit is low so that
you can enjoy high quality sound in playback.
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
SPEAKERS
XLR
RCA
HIGH
LOW
w q
w q
"6%*0
065
13&13&
065
Input select switch Operation mode select switch
NOTE
When using Bi-Wiring connection use 4 ~ 16 Ω/ohms speakers for the impedance.
Getting Started Connections and Settings Operations Troubleshooting
1.POA-A1HDCIEU.indd 12 2008/01/18 11:07:15
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon POA-A1HDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon POA-A1HDCI in the language / languages: English as an attachment in your email.

The manual is 5,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info