584591
8
Zoom out
Zoom in
Previous page
1/18
Next page
Connections and Settings
NOTE
Do not plug in the power cord until all connections have been completed.
When making connections, also refer to the operating instructions of the other components.
Be sure to connect the left and right channels properly (left with left, right with right).
Do not bundle power cords together with connection cables. Doing so can result in humming or noise.
Connections for all compatible audio signal formats are described in these operating instructions.
Please select the types of connections suited for the equipment you are connecting.
With some types of connections, certain settings must be made on the POA-A1HDCI. For details,
refer to the instructions for the respective connection items below.
Audio cables Signal direction
Analog connections (XLR)
Balanced cable
Analog connections (RCA)
Pin-plug cable
Speaker connections
Speaker cables
Audio signal:
Output
Input
Input
Output
Cables Used for Connections
Select the cables according to the equipment being connected.
Preparations
Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being
connected to the POA-A1HDCI, and be sure to interconnect the channels and polarities correctly.
1
Peel off about 0.03 ft / 10 mm of sheathing from the tip of the speaker
cable, then either twist the core wire tightly or terminate it.
2
Turn the speaker terminal counterclockwise to loosen it.
3
Insert the speaker cable’s core wire to the hilt into the speaker
terminal.
4
Turn the speaker terminal clockwise to tighten it.
NOTE
Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The
protection circuit may be activated if the core wires touch the rear panel or if the + and sides touch each
other (vProtection circuit).
Never touch the speaker terminals while the power supply is connected. Doing so could result in electric
shock.
Protection circuit
If speakers with an impedance lower than specified are used for an extended period of time with the
volume turned up high, the temperature may rise, activating the protection circuit.
When the protection circuit is activated, the speaker output is shut off and the power indicator flashes
red. If this happens, unplug the power cord, then check the speaker cable and input cable connections.
If the set is extremely hot, wait for it to cool off and improve ventilation around it. Once this is done, plug
the power cord back in and turn the set's power back on.
If the protection circuit is activated again even though there are no problems in the ventilation around the
set nor in the connections, the set may be damaged. Turn the power off, then contact a DENON service
center.
Connecting the speaker cables
When using a banana plug
Tighten the speaker terminal firmly before inserting the banana plug.
Getting Started Connections and Settings Operations Troubleshooting
1.POA-A1HDCIEU.indd 8 2008/01/18 11:06:59
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon POA-A1HDCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon POA-A1HDCI in the language / languages: English as an attachment in your email.

The manual is 5,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info