498788
13
Zoom out
Zoom in
Previous page
1/17
Next page
9
ENGLISH
Getting started
Basic connections Basic operation Troubleshooting Specifications IndexAdvanced connections Advanced operation Explanation terms
Connecting P.DIRECT jacks
If you use a preamplifier, connect it as shown below, and then you
can use this unit as a power amplifier.
Switching <POWER AMP DIRECT>hON”, allows the device
connected to the Power Amp Direct connector on the rear panel to
be played. When ON, the input indicator turns off.
Switching <POWER AMP DIRECT>jOFF”, allows the program
source selected using the INPUT SELECTOR knob to be played.
When OFF, the input indicator lights up.
For details on operations of the preamplifier, refer to the instruction
manual supplied with the preamplifier to be used.
w qw q
(R) (L)
L
R
L
R
Pre-amplifier
To PRE OUT jacks
Speaker
(L)
Speaker
(R)
NOTE
When the <POWER AMP DIRECT> switch is “hON”, adjustment
of the volume, balance and tone on the main unit has no effect.
Adjust the volume on the input device.
When the <POWER AMP DIRECT> switch is “hON”, the main unit
outputs at maximum volume. Check the output level on the input
device before playing it and adjust the volume accordingly.
Connecting pre out jacks
If you use a power amplifier or subwoofer, connect it as shown
below, and then you can use this unit as a preamplifier.
For connecting speaker systems, refer to the instruction manual
supplied with the power amplifier to be used.
R
L
R
L
Power-amplifier
To input jacks
NOTE
NEVER insert the short-circuiting pin plug into the PRE OUT
terminals. Doing so could result in damage.
Signals are output from the PRE OUT terminals even when using
headphones.
Advanced connections
Setting Eco mode
With the Eco mode ON, this unit will automatically enter the standby
mode after about 30 continuous minutes of no output from the
speakers or headphones. During standby mode with the Eco mode
ON, the Power indicator is unlit to reduce power consumption.
Press and hold [AMPLIFIER POWER] on the remote
control for at least 5 seconds.
Eco mode is switched between On and Off.
The Power indicator indicates Eco mode On/Off during Standby, as
shown below.
Eco mode “Off”
“Lit in red”
Eco mode “On”
“Unlit”
The Power indicator flashes in red during Eco mode setting.
If you set the Eco mode while the unit is ON, the unit will enter the
standby mode as soon as the Eco mode setting is completed.
The default setting for the Eco mode is OFF.
NOTE
If a source other than that selected with INPUT SELECTOR is
selected with <REC OUT SELECTOR>, this unit does not enter the
standby mode.
This unit enters the standby mode if it detects no output from
the source selected with INPUT SELECTOR. Therefore if a source
not selected with INPUT SELECTOR is output from the REC OUT
terminals, the function of automatically entering standby mode is
disabled to avoid interruption of power during recording.
Advanced operations
Advanced connections Advanced operation
1.PMA1510AEE2_ENG_002_5th_0222.indd 9 2010/02/23 15:55:18
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon PMA-1510AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon PMA-1510AE in the language / languages: English as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info