Manual Denon AVR-550SD (page 12 of 96) (German)

498717

Zoom out

Zoom in

1/96

This screen is not displayed when not using a subwoofer.

• Set the crossover frequency and subwoofer mode according to the speaker system being used.

• When using in combination with the SYS-550SD, we recommend turning the DSW-3L’s LF DIRECT switch on

and setting the AVR-550SD’s crossover frequency to 150 Hz. (See page 37.)

ENGLISH

Setting the type of speakers

Set whether or not speakers are connected and, if so, their size parameters.

• To select the speaker

1 FRNT Small

Press the (down) button to enter the settings and switch to the

SUBWOOFER MODE setting.

• Set up in function of your speaker systems. Performing this setup optimizes the system.

• The composition of the signals output to the different channels and the frequency response are adjusted

automatically according to the combination of speakers actually being used.

Center Sp. Front Sp.Front Sp.

Listening position

Surround back Sp.

Subwoofer

Surround Sp.

• To select the parameter

• Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.

Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient

volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the

subwoofer. (Example: SC-A3L, SC-C3L)

None…… Select this when no speakers are installed.

Yes/No…. Select “Yes” when a subwoofer is installed, “No” when it’s not installed.

• About the surround back speaker

When “S.Back. Sp.” is selected, the speaker systems change as described below.

When “NONE” is selected ..................................................................5.1ch speaker system

When “Large” or “Small” is selected and “1Speaker” is selected ....6.1ch speaker system

The surround back audio signals are output from both the speaker terminals and the PRE OUT connector’s

left channel. Connect one of these. A separate, commercially available pre-main (power) amplifier is

needed to connect the PRE OUT connector.

When “2 speaker” is selected ............................................................7.1ch speaker system

The surround back audio signals are only output from the PRE OUT connector. Connect a commercially

available pre-main (power) amplifier to output the audio signals. No sound is output from the “Surr. Back”

speaker terminals.

NOTE:

Select “Large” or “Small” not according to the physical size of the speaker, but according to the bass

reproduction capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to

“Small” and when set to “Large”, at a level that will not damage the speakers.

Caution:

In case the subwoofer is not used, be sure to set “Subwoofer = No”, or the bass sound of front channel is

divided to subwoofer channel and not reproduced in some mode.

If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when

“Small” is set for the front, center and surround speakers.

For the majority of speaker system configurations, using the Small setting for all five main speakers and

Subwooofer On with a connected subwoofer will yield the best results.

Setting the Subwoofer mode and Crossover Frequency

Select the “Subwoofer

Mode”.

Select the setting.

6 MODE NORM

Select the “Crossover

Frequency” mode.

Select the frequency.

7 C R . OVER 15 0

Press the ENTER button to enter the setting and switch to the DELAY TIME

setting.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-550SD in the language / languages: German as an attachment in your email.

The manual is 10,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Denon AVR-550SD Manual

Product: