584190
28
Zoom out
Zoom in
Previous page
1/96
Next page
Error Messages
If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the auto setup procedure over
again.
Error messages (examples) Cause Measures
or
Retry
Cancel
Microphone:None
Speaker :None
Auto Setup
Caution!
Included setup microphone is not connected.
Not all speakers could be detected.
Connect the included setup microphone to the SETUP
MIC jack on the main unit.
Check the speaker connections.
too high or
Retry
Cancel
Ambient noise is
Level is too low.
Auto Setup
Caution!
Too much noise in the room for accurate
measurements to be made.
Speaker or subwoofer sound is too low for
accurate measurements to be made.
Either turn off any device generating noise or move it
away.
Try again when the surroundings are quiet.
Check the speaker installation and the direction in
which the speakers are facing.
Adjust the subwoofer’s volume.
Retry
L :None
Cancel
Skip
Front
Auto Setup
Caution!
Displayed speaker could not be detected.
· The front L and front R speakers were not
properly detected.
· Only one channel of the surround speakers
was detected.
· Sound was output from the R channel
when only one surround back speaker was
connected.
· The surround back, but the surround speaker
was not detected.
Check the connections of the displayed speaker.
Retry
L :Phase
Cancel
Skip
Front
Auto Setup
Caution!
Displayed speaker connected with the
polarities reversed.
Check the polarities of the displayed speaker.
For some speakers, this error message may be
displayed even if the speaker is properly connected. In
this case, select “Skip”.
NOTE
Be sure to turn the power off before checking the speaker connections.
Room EQ
Select room EQ setting method.
[Selectable items]
All
: Apply settings to all surround modes.
Assign
: Make settings for each surround mode separately.
s
Option
Select settings for room EQ, mic, etc.
Select “Retry” to make the measurements again.

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Direct Mode Setup
Select room EQ use for DIRECT or PURE DIRECT mode.
[Selectable items]
ON
: Use room EQ.
OFF
: Do not use room EQ.
Mic Select
Select the microphone type if not using supplied mic.
The microphone connected to V.AUX Lch is used.
[Selectable items]
Mic
: Supplied mic is being used.
V.AUX L
: Other mic connected to V.AUX is used.
d
Parameter Check
Check auto setup measurement results.
This is displayed after the auto setup procedure is completed.
[Items to be checked]
Speaker Config. Check
Distance Check
Channel Level Check
Crossover Freq. Check
EQ Check
The auto setup results can be set again when “Restore” is selected.
AVR2808CIEU.indd 28 2007/06/20 8:58:01
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-2808CI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-2808CI in the language / languages: English as an attachment in your email.

The manual is 12,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-2808CI

Denon AVR-2808CI User Manual - English - 93 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info