584190
27
Zoom out
Zoom in
Previous page
1/96
Next page
The speaker connection status and the speaker polarities are detected at
the main listening position. At this time, the listening environment with
respect to the main listening position (“Speaker size check”, “Distance
correction, “Channel level adjustment”, “Crossover frequency check”
and “Room EQ correction”) is measured automatically at the main
listening position.
Once the measurements are completed, the results of the speaker
connection are displayed.
Step 1 : Speaker Detection
Auto Setup
Optimize settings for speakers in use.
F Menu screen F
1-1.Start Menu
Step1:Speaker Detection
at ear height at
Front Sp. A
Amp Assign
Start
Cancel
Please place microphone
main listening position.
Start
Start auto setup and output the test tone.
NOTE
Loud test tones are output during the measurements. Be careful
when measuring at night or when there are small children nearby.
Do not stand between the speakers and setup microphone or allow
obstacles between them while the measurements are being made.
Obstacles will make it impossible to measure correctly.
Keep as quiet as possible during measurements. Loud sounds in the
area will make it impossible to measure correctly.
Operating the MASTER VOLUME knob on the main unit or the VOL
+/– buttons on the remote control unit during the measurements will
cancel the measurements.
Do not change the speaker connections or subwoofer volume after
“Step 1”.
a Start Menu
The settings are performed automatically.
NOTE
Do not turn the power off while the settings are being stored in the
memory.
Step 2 : Measurements
The listening environment with respect to the listening position
(“Speaker size check”, “Crossover Frequency check” and “Room EQ
correction”) is measured automatically at positions 2 to 8.
Once a measurement is made, move the setup microphone to the
next position.
Measure a total of at least 6 positions (main listening position and at
least 5 other surrounding positions). Measurements can be completed
even if only taken in 5 positions, but for better results we recommend
taking them in 6 or more positions. (Measurements can be taken in
a maximum of 8 positions.)
Step 3 : Calculation
When “Calculate is selected at “Step 2”, the speaker system is
analyzed automatically.
The time required for this analysis depends on the number of speakers
connected. The more the number of speakers, the longer the time
required for analysis.
Step 4 : Check
Once the auto setup procedure is completed, a measuring result
checking screen appears.
Select any item whose measuring results you want to check and check
the results.
Values that are different from the actual distance may be set for
speakers with built-in fi lters (subwoofers, etc.).
Step 5 : Store
The auto setup measurement results are stored.
Front Speaker
The front speaker to be measured can be selected ahead of time
here.
[Selectable items]
A
: Output test tone from front speakers A.
B
: Output test tone from front speakers B.
A + B
: Output test tone from front speakers A and B.
Amp Assign
Advanced setting : changes power amplifi er assignment.
For details, refer to Amp Assign” (vpage 31).
If an error message appears during the measurements, check “Error
messages”, take the necessary countermeasures, then redo the
measurements (vpage 25).

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Set as desired before starting the auto setup procedure.
AVR2808CIEU.indd 27 2007/06/20 8:58:01
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-2808CI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-2808CI in the language / languages: English as an attachment in your email.

The manual is 12,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-2808CI

Denon AVR-2808CI User Manual - English - 93 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info