498701
14
Zoom out
Zoom in
Previous page
1/50
Next page
14
ENGLISH
Check of the measurement results
1
Select the items.
The measurement results of each item can be checked
here.
(Remote control unit)
2
Press the ENTER button and display the verification screen.
(Remote control unit)
[Speaker Config. Check] [Delay Time Check] [Channel Level Check]
NOTE:
When measurements have been made using the measurement microphone,
speakers with a built-in filter such as subwoofers might be set with a value
that differs from the physical distance because of the internal electrical delay.
3
If the check ends, press the ENTER button again.
(Remote control unit)
4
Select from the following three items based on the
measurement results.
•Store : Set with the checked measurement
value.
Retry : Perform the measurement again.
Cancel : Cancel the checked measurement
value.
(Remote control unit)
5
When the “Store” is selected, all parameters are
stored up and switch to the SUBWOOFER MODE
setting.
(Remote control unit)
Setting the type of speakers
1
Set whether or not speakers are connected and, if so, their size parameters.
2 FRONT LARGE
2
Press the ENTER or (down) button to enter the settings and switch to the
SPEAKER DISTANCE setting.
Set up in function of your speaker systems. Performing this setup optimizes the system.
The composition of the signals output to the different channels and the frequency response are adjusted
automatically according to the combination of speakers actually being used.
Center Sp. Front Sp.Front Sp.
Listening position
Surround back Sp.
Subwoofer
Surround Sp.
Surround Sp.
•To select the parameter
Parameters
Large.................Select this when using speakers that have sufficient performance for reproducing bass sound
below the frequency set for the Crossover Frequency mode.
Small.................Select this when using speakers that do not have sufficient performance for reproducing bass
sound below the frequency set for the Crossover Frequency mode. When this is set, bass
sound with a frequency below the frequency set for the Crossover Frequency mode is sent
to the subwoofer.
None .................Select this when no speakers are installed.
Yes/No...............Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.
2spkrs/1spkr .....Set the number of speakers to be used for the surround back channel.
If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when
“Small” is set for the front, center and surround speakers.
(Remote control unit)
(Remote control unit)
•To select the speaker
(Remote control unit)
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Denon AVR-2105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Denon AVR-2105 in the language / languages: English as an attachment in your email.

The manual is 3,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Denon AVR-2105

Denon AVR-2105 User Manual - German - 91 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info