634638
3
Zoom out
Zoom in
Previous page
1/8
Next page
8
Water penetrating the coee machine could cause
damage.
Do not place the appliance near taps or sinks.
The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
The appliance gives o heat.
After positioning the appliance on the worktop, leave a
space of at least 3 cm between the surfaces of the appli-
ance and the side and rear walls and at least 15 cm above
the coee machine.
Connecting the appliance
Danger!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an eciently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
electrician.
FILLING THE WATER TANK
1. Open the lid of the appliance (g. 1) then extract the tank
by pulling upwards (g. 2);
2. Fill the tank with fresh clean water, taking care not to ex-
ceed the MAX level (g. 3).
Put the tank back in the appliance, pressing lightly to open
the valves located on the bottom of the tank.
3. More simply, the tank can also be lled without removing
it, pouring the water directly from a jug.
Important:
Never operate the appliance without water in the tank or with-
out the tank.
Check the level of water in the tank through the viewing win-
dow (A12).
SETTING UP THE APPLIANCE
Important: Everytime you switch on the appliance, make sure that the
mode selector dial (B1) is turned to I position (Stand-by).
1. Turn the appliance on by pressing the ON/OFF button (g.
4): the power light I comes on.
2. Insert the required coee lter in the lter holder (g. 5).
3. Attach the lter holder onto the machine without lling it
with ground coee (g. 6).
4. Place a 0.5 litre container under the boiler outlet and an-
other 0.5 litre container under the cappuccino maker.
5. Wait until the OK light comes on (g. 8) and immediately
afterwards turn the mode selector dial to the
position (g. 9) and deliver about half the tank through the
lter holder.
6. Then turn the steam dial to the position (g. 10)
and deliver all the water remaining in the tank through the
cappuccino maker.
7. Turn the steam dial back to the 0 position and the mode
selector dial to the l position (STAND-BY).
8. Empty the two containers and replace them under the
boiler outlet and the cappuccino maker and repeat points
5-6-7.
Now the appliance is ready for use.
Auto-o
If the appliance is not used for a certain period of time (variable
according to the model), it turns o automatically (the power
light goes out).
Tips for a hotter coee
To make espresso coee at the right temperature, the coee
maker should be preheated as follows:
1. Turn the appliance on by pressing the ON/OFF switch (the
ON light comes on) (g. 4) and attach the lter holder to
the appliance without adding pre-ground coee (g. 6).
2. Place a cup under the lter holder. Use the same cup as will
be used to prepare the coee in order to preheat it.
3. Wait until the OK light comes on (g. 8) and immediately
afterwards turn the selector dial to the position
(g. 9) and let water discharge until the OK light turns o,
then interrupt by turning the dial to the I position.
4. Empty the cup, wait until the OK light comes on again and
then repeat the same operation.
(It is normal for a small and harmless pu of steam to be given
o when removing the lter holder).
Mugs or glasses tray (models ECP35.31 and
ECP33.21 only)
If you are using tall cups or glasses (for example, to make long
coee or macchiato),extract the drip tray and rest the cup di-
rectly on the mugs or glasses tray (A14 - g. 11).
Once you have made your coee, put the drip tray back in
position.
HOW TO MAKE ESPRESSO COFFEE USING PRE
GROUND COFFEE
Important: Everytime you switch on the appliance, make sure that the
mode selector dial (B1) is turned to I position (Stand-by).
1. Place the ground coee lter (C2 or C3) in the lter holder.
Use the lter to make one coee or the
lter to make two coees.
2. To make just one coee, place one level measure of pre-
ground coee (about 7 g) in the lter. (g. 12).
To make two coees, place two loosely lled measures
(about 6+6 g) of pre-ground coee in the lter.
Fill the lter a little at a time to prevent the pre-ground
coee from overowing.
Important: For correct operation, before lling with pre-ground coee,
make sure there are no coee residues left in the lter from the last time you made
coee.
3. Distribute the pre-ground coee evenly and press light-
ly with the presser (g. 13). Correct pressing of the pre-
ground coee is essential to obtain a good espresso. If
pressing is excessive, coee delivery will be slow and the
froth will be dark. If pressing is too light, coee delivery
will be too rapid and the froth will be skimpy and light
coloured.
4. Remove any excess coee from the rim of the lter holder
and attach to the appliance. Turn the handle rmly to-
wards the right (g. 6) to avoid water leaking out.
5. Place the cup or cups under the lter holder spouts (g.
14). You are recommended to warm the cups before mak-
ing coee by rinsing them with a little hot water.
6. Make sure the OK light (g. 8) is on (if o, wait until
it comes on), then turn the mode selector dial to the
position. When the desired amount of coee
has been delivered, turn the dial to the l position.
7. To remove the lter holder, turn the handle from right to
left.
Danger of burns! To avoid splashes, never remove the lter holder while
the appliance is delivering coee.
8. To turn the appliance o, press the ON/OFF button.
HOW TO PREPARE ESPRESSO COFFEE USING PODS
1. Preheat the appliance as described in the section Tips for
a hotter coee, making sure the lter holder is attached.
This obtains a hotter coee.
Please note: Use pods conforming to the ESE standard, indicated on the
pack by the following symbol.
The ESE standard is a system accepted by leading pod producers and enables espresso
coee to be prepared simply and cleanly.
2. Place the pod coee lter (C4 ) in the lter holder.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeLonghi ECP 33.21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeLonghi ECP 33.21 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeLonghi ECP 33.21

DeLonghi ECP 33.21 User Manual - German - 8 pages

DeLonghi ECP 33.21 User Manual - Dutch - 8 pages

DeLonghi ECP 33.21 Quick start guide - All languages - 22 pages

DeLonghi ECP 33.21 Quick start guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info