555837
15
Zoom out
Zoom in
Previous page
1/32
Next page
15
GB
TROUBLE SHOOTING
NOITCA EVITCERROCESUAC ELBABORPMELBORP
Engine does not start.
Throttle chock not in the correct
position for the prevailing conditions.
Move throttle chock to correct position.
Fuel tank is empty.
Fill tank with fuel.
Air cleaner element is dirty.
Clean air cleaner element.
.mN 03 - 52 ot gulp kraps nethgiT.esool gulp krapS
Spark plug wire loose or disconnected
from plug.
Install spark plug wire on spark plug.
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to 0.8 mm.
Spark plug is defective.
Install new, correctly gapped plug.
Carburetor is flooded with fuel.
Remove air cleaner element and pull starter rope
continuously until carburetor clears itself and install
air cleaner element.
Faulty ignition module. Contact SBM-Group authorised service centre.
Engine difficult to
loses pstart or ower.
Dirt, water, or stale fuel tank.
Drain fuel and clean tank. Fill tank with clean, fresh
fuel.
Vent hole in fuel tank cap is plugged. Clean or replace fuel tank cap.
Air cleaner element is duty. Clean air cleaner element.
Engine operates
erratically.
Spark plug is detective.
Install new, correctly gapped plug.
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to 0.8 mm.
Air cleaner element is dirty.
Clean air cleaner element.
Engine idles poorly.
Air cleaner element is dirty.
Clean air cleaner element.
Air slots in engine shroud are blocked. Remove debris from shots.
Cooling fins and air passages under
engine blower housing are blocked.
Remove debris from cooling fins and air passages.
Engine skips at high
speed.
Gap between electrodes of spark plug
is too close.
Set gap between electrodes at 0.7 to 0.8 mm.
Engine overheats.
Cooling air flow is restricted.
Remover any debris from slots in shroud, blower
housing, air passages.
Incorrect spark plug.
Install RJ19LMC spark plug and cooling fins on
engine.
Mower vibrates
abnormally.
Cutting assembly is loose. Tighten blade.
Cutting assembly is unbalanced. Balance blade.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DLM-2600-G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DLM-2600-G in the language / languages: All languages as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info