555837
14
Zoom out
Zoom in
Previous page
1/32
Next page
14
GB
STORAGE INSTRUCTIONS
(OFF SEASON)
The following steps should be taken to prepare lawn
mower for storage.
1. Following the nal cut of the season allow the fuel
tank to run dry.
2. Clean and lubricate mower thoroughly as described
in the lubrication instructions.
3. Refer to engine manual for correct engine storage
instructions.
4. Lightly coat mower’s cutting blade with chassis
grease to prevent rusting.
5. Store mower in a dry, clean area.
NOTE:
- When storing any type of power equipment
in an unventilated or material storage shed;
- Care should be taken to rust-proof the equipment.
Using a light oil or silicone, coat the equipment,
especially cables and all moving parts.
- Be careful not to bend or kink cables.
- If the starter rope becomes disconnected from rope
guide on handle, disconnect and ground the spark
plug wire, Depress the blade control handle and pull
the starter rope out from engine slowly. Slip the starter
rope into the rope guide bolt on handle.
ENGINE AIR CLEANER
CAUTION: Do not allow dirt or dust to clog
the air lter foam element.
The engine air cleaner element must be
serviced (cleaned) after 25 hours normal mowing. The
foam element must be serviced regularly if the mower
is used in dry dusty conditions.
TO CLEAN AIR FILTER
1. Remove screw.
2. Remove cover.
3. Wash lter element in soap water. DO NOT USE
GASOLINE!
4. Air dry lter element.
5. Place a few drops of SAE30 oil on the foam lter and
squeeze tightly to remove any excess oil.
6. Reinstall lter.
NOTE: Replace lter if frayed, torn, damaged
or unable to be cleaned.
CUTTING BLADE
CAUTION: Be sure to disconnect and ground
the spark plug wire before working on the
cutting blade to prevent accidental engine
starting. Protect hands by using heavy gloves or a rag
to grasp the cutting blades.
WARNING: Periodically inspect the blade
adapter for cracks, especially if you strike a
foreign object. Replace when necessary. For
best results your blade should be sharp. The blade
may be resharpened by removing it and either grinding
or ling the cutting edge keeping as close to the original
bevel as possible. It is extremely important that each
cutting edge receives an equal amount of grinding to
prevent an unbalanced blade. Improper blade balance
will result in excessive vibration causing eventual
damage to the engine and mower.
BLADE MOUNTING TORQUE
Center Bolt must be tightened to 35 - 45 Nm torque. To
insure safe operation of your unit. ALL nuts and bolts
must be checked periodically for correct tightness. After
prolonged use, especially in sandy soil conditions, the
blade will become worn and lose some of the original
shape. Cutting ef ciently will be reduced and the blade
should be replaced. Replace with an approved factory
replacement blade only. Possible damage resulting
from blade unbalance condition is not the responsibility
of the manufacturer.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DLM-2600-G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DLM-2600-G in the language / languages: All languages as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info