Manual De Walt D25500K T-3 (page 32 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Norwegian, Finnish)

591271

Zoom out

Zoom in

1/132

ENGLISH

OPERATION

Instructions for Use

WARNING:

• Always observe the safety

instructions and applicable

regulations.

• For your own safety, always use the

tool with both hands.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to

the tool (approx. 20 kg). Excessive

force does not speed up drilling

or chiselling but decreases tool

performance and may shorten

tool life.

Proper Hand Position (ﬁ g. 1)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (h), with the other hand on the main

handle (l).

Switching On and Off (ﬁ g. 1)

1. To switch on the tool, press the on/off

switch (a).

2. To stop the tool, release the switch.

Drilling with a Solid Bit (ﬁ g. 1)

1. Insert the appropriate drill bit.

2. Set the mode selector switch (d) to the

“hammerdrilling” position.

3. Set the electronic speed and impact control

dial (b).

4. Fit and adjust the side handle (h).

5. If necessary, set the drilling depth.

6. Mark the spot where the hole is to be drilled.

7. Place the drill bit on the spot and switch on the

tool.

8. Always switch off the tool when work is finished

and before unplugging.

Drilling with a Core Bit (ﬁ g. 1)

1. Insert the appropriate core bit.

2. Assemble the centerdrill into the core bit.

3. Set the mode selector switch (d) to the

“hammerdrilling” position.

4. Turn the electronic speed and impact control

dial (b) to a medium or high speed setting.

5. Fit and adjust the side handle (h).

6. Place the centerdrill on the spot and switch on

the tool. Drill until the core penetrates into the

concrete approx. 1 cm.

7. Stop the tool and remove the center drill. Place

the core bit back into the hole and continue

drilling.

NOTE: When drilling through a structure thicker

than the depth of the core bit, break away the

round cylinder of concrete or core inside the bit

at regular intervals.

8. To avoid unwanted breaking away of concrete

around the hole, first drill a hole the diameter of

the centerdrill completely through the structure.

Then drill the cored hole halfway from each side.

9. Always switch off the tool when work is finished

and before unplugging.

Chipping and Chiselling (ﬁ g. 1)

1. Insert the appropriate chisel and rotate it by

hand to lock it into one of 8 positions.

2. Set the mode selector switch (d) to the

“hammering only” position.

3. Set the electronic speed and impact control

dial (b).

4. Fit and adjust the side handle (h).

5. Switch on the tool and start working.

6. Always switch off the tool when work is finished

and before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of De Walt D25500K T-3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 4,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

De Walt D25500K T-3 Manual

Product: