Manual De Walt D25500K T-3 (page 31 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Norwegian, Finnish)

591271

Zoom out

Zoom in

1/132

ENGLISH

2. Insert the bit shank into the tool holder (f), and

press and turn the bit slightly until the sleeve

snaps into position.

3. Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

4. To remove a bit pull back the tool holder locking

sleeve (f) and pull the bit out of the tool holder.

Selecting the Operating Mode

(ﬁ g. 5)

The tool can be used in two operating modes:

Hammerdrilling: for concrete and

masonry drilling operations.

Hammering only: for light chipping,

chiselling and demolition applications.

In this mode the tool can also be used

as a lever to free a jammed drill bit.

1. To select the operating mode, press the safety

lock (e) and rotate the mode selector switch

(d) until it is points to the symbol of the required

mode.

2. Release the safety lock and check that the

mode selector switch is locked in place.

Indexing the Chisel Position (ﬁ g. 5, 6)

The chisel can be indexed and locked into 8 different

positions (fig. 6).

1. Rotate the mode selector switch (d) until it

points upward.

2. Rotate the chisel in the desired position.

3. Set the mode selector switch (d) to the

“hammering only” position.

4. Twist the chisel until it locks in position.

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 2)

Turn the dial (b) to the desired level. The higher the

number, the greater the speed and impact energy.

With dial settings from 1 (low) to 5 (full power) the

tool is extremely versatile and adaptable for many

different applications. The required setting is a matter

of experience. e.g.:

— when chiselling or drilling in soft, brittle

materials or when minimum break-out is

required, set the dial to 1 or 2 (low);

— when breaking or drilling in harder

materials, set the dial to 5 (full power).

D25600

With dial settings from 1 to 7 the tool allows a further

fine-adjustment to the choice of application.

Assembling and Fitting the Side

Handle (ﬁ g. 7–10)

The side handle (h) can be mounted in front or in

rear position on either side of the machine to suit

both RH- and LH-users.

CAUTION: Always operate the tool with

the side handle properly assembled.

MOUNTING IN FRONT POSITION (FIG. 7, 8)

1. Snap the steel ring (p) over the collar (g) behind

the tool holder (f). Squeeze both ends together,

mount the bush (n) and insert the pin (o).

2. Place the side handle clamp (m) and screw on

the clamp wheel (i). Do not tighten.

3. Screw the side handle (h) into the clamp wheel

and tighten it.

4. Rotate the side handle mounting assembly to

the desired position. For drilling horizontally

with a heavy drill bit, we recommend to place

the side handle at an angle of approx. 20° for

optimum control (fig. 8).

5. Lock the side handle mounting assembly in

place by tightening the clamp wheel (i).

MOUNTING IN REAR POSITION (FIG. 9, 10)

The rear position is particularly useful when drilling

overhead or down into a floor. Refer to fig. 10.

1. Unscrew the side handle (h) and remove it

from the front position. Leave the side handle

mounting assembly in front position so that the

depth adjustment rod can still be used.

2. Screw the side handle directly into one of the

rear side handle positions (j) on either side of the

tool.

Setting the Drilling Depth (ﬁ g. 11)

1. Insert the required drill bit.

2. Loosen the clamp nut (q) and fit the depth

adjustment rod (k) through the hole in the side

handle clamp.

3. Push the drill bit into a surface at a right angle

and adjust the depth adjustment rod (k) as

shown.

4. Tighten the clamp nut (q).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of De Walt D25500K T-3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 4,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

De Walt D25500K T-3 Manual

Product: