609083
67
Zoom out
Zoom in
Previous page
1/84
Next page
67
GT 530ADDR_G30A/AE _IO_V4.0 09/2013
67
GT 530A DDRA 001 v1.0 06/2010
S2NA (ME50) or S3NA (MD5) Temperature control panel (Field Wiring Diagram)
Internal wiring by DDR-De Dietrich Factory
1 2 3
4
5 6
7
9 10
11
8 13 14
12
16
15
18 1917
21
20 23
24
22 2625 28 29
27
3130
33
3432 3635 38
37
120/60/1
Main Power Supply
Optional
thermostat TT
connection
CS – Safety
Contact 120v
1
st
Stage
2
nd
stage
N Gnd
Heating
Pump
Relay
L
N X
X
Limit Circuit
X X
2
nd
stage
controller
Burner Connections
L
N
Burner main
power
DHW
Pump
120/24v
Transformer
Burner Connections
Main Power 120/60/1
External Controller External control sensor wiring
Optional field wiring
terminals for
external control
Terminals for Optional Digital Control
or external control
1
2
3
4
5 6
1
2
3
4
5
6
Field Wiring Callout Notes
Fuse disconnect 15A Max.
Service Switch
Low water cut-off control
External Limit (Optional)E xternal Start/Run Interlock (Optional)
X
= Terminal designation
consult burner wiring
diagram or manufacturer
Vent Safety Switch, unless burner is
equipped with High gas or Pressure switch
Burner motor power supply may be from seperate disconnect if power
exceed 120V ±10% - 10A @ 60Hz. Or is multi-phase
WARNING
FAILURE TO FOLLOWING THIS WIRING
DIAGRAM MAYRESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY INCLUDING DEATH.
Wiring must be in strict compliance with CSA
C22.2 and NEC/NFPA 70. All wiringshown
supplied and wired by others. Optional 2
nd
stage relay supplied by others or ordered
loose, relay can be mounted in panel or
directly on burner.
This equipment must be earth bonded or
grounded.All wiring (eld or replacement)
must be min 18AWG type CSA TEW/ UL 1015
rated 105°C or an approved equivalent. All
wiring and panels must be shielded from spray
or ingestion of water. Any portion of the control
which has been subject to spray or ingestion
of water, the entire control must be replaced.
It is the responsibility of the installer/owner to
verify the controls are functioning correctly and
are adjusted correctly.Suitable wire protection
and strain relief’s are required (upstream &
downstream) of the control panel. Line voltage
wiring and low voltage sensor wiring must use
separate wire conduits.
LABEL ALL WIRES PRIOR TO DISCONNECTING
THEM FOR SERVICE.
Field wiring shown (By Others)
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for De Dietrich GT 530A Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of De Dietrich GT 530A Series in the language / languages: English as an attachment in your email.

The manual is 13,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info