609083
17
Zoom out
Zoom in
Previous page
1/84
Next page
17
GT 530ADDR_G30A/AE _IO_V4.0 09/2013
and bathroom exhausts, so they will operate at
the maximum speed. Do not operate a summer
exhaust fan. Close re place dampers.
(d) Place in operation the appliance being inspected.
Follow the lighting instructions. Adjust thermostat
so appliance will operate continuously,
(e) Test for leakage at the draft hood relief opening
after 5 minutes of main burner operation.
(f) After it has been determined that each appliance
remaining connected to the common venting
system properly vents when tested as outlined
above, return doors, windows, exhaust fans,
replace dampers and any other gas-burning
appliance to their previous condition of use,
(g) Any improper operation of the common venting
system should be corrected so the installation
conforms with the National Fuel Gas Code, ANSI
Z223.1 and/or CAN/CGA B149 Installation Codes.
When resizing any of the common venting system,
the common venting system should be resized to
approach the minimum size as determined using
the appropriate tables in Part II of the National Fuel
Gas Code, ANSI Z223.1 and/or CAN/CGA B149,
Installation Codes.
(h) The minimum distance from adjacent public
walkways, adjacent buildings, openable windows
and building openings shall not be less than those
values specied in the National Fuel Gas Code ANSI
Z223.1 and/or CAN/CGA B149, Installation Codes.
A : Chimney connection :
- GT 530A-15 to 530A-21 = 16”/400 mm
- GTE 530A-22 to GT 530A-25 = 18”/450 mm
- GT 530 -32 AE = 20"/508 mm
The boiler must be connected to a chimney-venting
system that will safely discharge all ue gases to the
outside in an effective manner.
The boiler breeching and chimney venting must be
sized according to local and national code require-
ments.
Replacement procedures
___________________________________________________________________________________ ______________________ _______________________________________________
When an existing boiler is removed from a common
venting system, the common venting system is
likely to be too large for proper venting of the
appliances remaining connected to it.
At the time of removal of the existing boiler,
the following steps shall be followed with each
appliance remaining connected to the common
venting system placed in operation, while the other
appliances remaining connected to the common
venting system are not in operation.
(a) Seal any unused openings in the common venting
system,
(b) Visually inspect the venting system for proper
size and horizontal pitch and determine there is
no blockage or restriction, leakage, corrosion and
other deciencies which could cause an unsafe
condition,
(c) Insofar as is practical, close all building doors and
windows and all doors between the space in which
the appliances remaining connected to the common
venting system are located and the other spaces
of the building. Turn on clothes dryers and any
appliance not connected to the common venting
system.
Turn on any exhaust fans such as range hoods
Installation Specications
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for De Dietrich GT 530A Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of De Dietrich GT 530A Series in the language / languages: English as an attachment in your email.

The manual is 13,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info