535590

Datalogic QuickScan QD2430 Manual

25
Zoom out
Zoom in
Previous page
1/48
Next page
Operating Modes
Quick Reference Guide 21
Operating Modes
Scan Mode
The imager can be set to operate in one of several scanning
modes. See the PRG for more information and settings for any
of the options:
Trigger Single (Default):
This mode is associated with typical
handheld reader operation. When the trigger is pulled, illumi-
nation is turned on and the scanner attempts to read a label.
Scanning is activated until one of the following occurs:
• the programmable “maximum scan on time”
1
has
elapsed
• a label has been read
• the trigger is released
Trigger Pulse Multiple:
Scanning begins when the trigger is
pulled and continues after the trigger is released, until the trig-
ger is pulled again or until the programmable “maximum scan
on time”
1
has elapsed. Reading a label does not disable scan-
ning. Double Read Timeout
1
prevents undesired multiple
reads while in this mode.
Trigger Hold Multiple :
When the trigger is pulled, scanning
starts and the product scans until the trigger is released or
“maximum scan on time”
1
has elapsed. Reading a label does
not disable scanning. Double Read Timeout
1
prevents unde-
sired multiple reads while in this mode.
Always On:
The illuminator is always ON and the reader is al-
ways ready for code reading. Double Read Timeout
1
prevents
undesired multiple reads.
Flashing:
The reader illuminator flashes on and off regardless
of the trigger status. Code reading takes place only during the
Flash On
2
time. Double Read Timeout
1
prevents undesired
multiple reads.
Object Detection:
The scanner looks for changes within its
field-of-view. The Aiming Pattern is always on to show the op-
timum reading area. If a predefined amount of movement is
detected, the red illumination switches on. Scanning contin-
ues until a label is read or "maximum scan on time" is reached.
1. See the Product Reference Guide (PRG) for these and other programmable
features
2. Controlled by Flash On Time and Flash Off Time. Use the PRG to program these
options.
… 25 …


Need help? Post your question in this forum.

Forumrules
1

Forum

datalogic-quickscan-qd2430

Reset search

  • I am using QD 2430 with L18ER rs 232 Communication.
    After Power cycle once it will scan after that it will start the blinking and not scan other barcode to scan it need to take again power cycle. Submitted on 24-1-2020 at 16:46

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Datalogic QuickScan QD2430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Datalogic QuickScan QD2430 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info