Manual Danfoss TPOne-M (page 19 of 28) (English)

654610

Zoom out

Zoom in

1/28

Danfoss Heating

Daylight

Saving

Choose to set automatic daylight saving changes

on or o.

Default: On

Button Lock Button lock can be set to avoid unintentional

setting changes. To activate buttons while button

lock is active the user must press the OK button

for 5 seconds.

Default: O

Display Idle

Mode

When the TPOne is in idle mode the display can be

set to go o. The display will come on when any

button is pressed.

Default: On

External

Sensor

TPOne includes an optional external sensor input.

If tted select the type of external sensor:

None - No external sensor tted

Room Sensor - Remote room sensor tted. This

will take priority over the TPOne internal sensing.

Danfoss part TS2A - sold seperately

Window Sensor - Where a window sensor has

been tted the TPOne will go into standby mode

while the window is open. Window open feature

is activated 60secs after input is made open circuit.

Window open feature is deactivated 30secs after

input is made closed circuit.

Floor Limit Sensor - This allows for a thermostat

limit sensor to be set, typical application is oor

heating. If the temperature sensed by the limit

sensor exceeds the limit setting the output will be

turned o until the temperature has dropped by

2°C. A warning will be shown on the display that

the oor limit temperature has been exceeded.

Room temperature will be controlled by the

TPOne internal sensor.

The temperature set for the limit point sensor will

be determined by the type of oor.

The recommended limits are:

Tiles on chipboard and wooden oors 27°C

Carpet or vinyl on chipboard 35°C

Tiles on concrete oor 40°C

Concrete, screed, etc 45°C

Danfoss Part TS3 - sold seperately

Lockout - Where a Key lockout switch is tted

the TPOne can be forced into the standby mode

remotely. While activated none of the buttons

can be used and the TPOne will only call for heat

if room temperature falls below set frost protect

level. Lockout feature is activated 60secs after

input is made open circuit. Feature is deactivated

30secs after input is made closed circuit.

Installer Settings (Continued)

On both, one on ground floor and another on first floor, of our TPOne-M we are having exactly the same problems with. When you press 'Home Mode' the +1,2,3 hour boosts is no longer appearing or happening. Scheduled times not operating when set on schedule. Theses units came fitted in our new build property that we purchased July 2022. Submitted on 16-11-2024 at 11:51
Reply Report abuse
What I need to do if show external sensors fail and I can set up temperature? Submitted on 9-11-2021 at 21:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Danfoss TPOne-M in the language / languages: English as an attachment in your email.

The manual is 2,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Danfoss TPOne-M Manual

Product: