643443

Daihatsu Terions J100 Manual

36
Zoom out
Zoom in
Previous page
1/1009
Next page
3. Inspection and adjustment of valve clearance
The measurement and adjustment of the valve clearance
are carried out when each piston of the No. 1 and No. 4
cylinders is set to the top dead center at the end of com-
pression stroke.
WARNING:
· Never burn yourself with hot engine components,etc.
during operation.
CAUTION:
· The valve clearance adjustment is performed normally
when the engine is in a hot condition.
· “HOT engine condition” denotes a condition in which
the cooling water temperature is 75 - 85°C and the en-
gine oil temperature is above 65°C.
However, when the engine has been overhauled, it is
necessary to adjust the valve clearances while the en-
gine is cold and to readjust the valve clearance in a hot
condition after warming up the engine.
MA–18
(1) Warm up the engine thoroughly. (Only when neces-
sary.)
(2) Remove the air cleaner.
(Refer to the Inspection of spark plug section for re-
moval.)
(3) Remove the resistive cords and ignition coils.
(Refer to the removal of resistive cords and ignition coil
in the inspection of the spark plug section.)
(4) Disconnect the PCV hoses(blow-by gas hose) from the
cylinder head cover.
(5) Remove the bolt attaching the timing belt cover to the
cylinder head cover.
(6) Loosen the eight attaching bolts (6 mm) shown in the
figure over two or three stages in the sequence in the
right figure.
(7) Remove the cylinder head cover by removing the at-
taching bolts.
CAUTION:
· Never damage the spark plug grommets of the spark
plug tubes and cylinder head cover gasket during the
removal of the cylinder head cover.
(8) Inspection and adjustment of valve clearances
CAUTION:
· Before the adjusting screw is tightened with lock nuts,
apply engine oil to between the lock nut and the valve
rocker arm.
q Remove the engine undercover by removing the
six attaching bolts.
w Turn the crankshaft until the recessed mark on the
crankshaft pulley is aligned with the indicator mark
on the timing belt cover.
w
u
t
e
r
y
i
q
Timing mark
Indicator
JMA00047-00038
JMA00048-00039
JMA00049-00040
JMA00050-00041
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Daihatsu Terions J100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Daihatsu Terions J100 in the language / languages: English as an attachment in your email.

The manual is 41,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info