467056
9
Zoom out
Zoom in
Previous page
1/12
Next page
L. Remote sensor battery low indicator
Appears when the batteries of the remote sensor are running dry and the temperature measured by this sensor is no longer
reliable. The user must change the batteries at once.
DESCRIPTION OF BUTTONS
TTA303 has 7 major function buttons on top, front and back.
1. [LIGHT-SNOOZE]
Press once to turn backlight on for 5 seconds;
Stop alarm sound temporary for 8 minutes when alarm sounds;
2. [CLOCK]
Toggle for clock, calendar or alarm display mode;
Clock HR:MIN Calendar Day-MON Alarm HR:MIN
(unit auto returns to clock display mode after viewing either calendar or alarm display for 10 seconds)
Press 2s to activate setting mode for corresponding displayed mode – clock/calendar/alarm
3. [MEM]
Toggle for max or min temperature memory reading for both IN & OUT thermometers
Press and hold 2 seconds to clear both IN/OUT temperature memory;
4. [CH]
Toggle to display remote thermo channel from channel 1, channel 2, channel 3 to Auto-scroll mode which alternately
display 3 channels;
Press and hold 2 seconds to activate searching mode for remote sensor;
5. [ALERT]
Toggle to display high temperature alert and then low temperature alert for indoor thermometer, channel 1, 2, 3
remote thermometers respectively and then return to normal thermo display mode; Press & hold for 2 seconds at the desired
alert temperature display to enter its setting mode, use [+] / [-] keys to change the settings, press [ ] again to conrm
the setting or press on key for 5 seconds to auto-exit to normal thermo display and conrm the setting;
6. + [UP]
Increase the setting
Press and hold 2 seconds to manually activate radio controlled function; press once again deactivate radio controlled function;
7. - [DOWN]
Decrease the setting
Toggle Daily Alarm on/off when display shows Alarm mode;
Toggle Alert on/off when display shows corresponding Temperature Alert mode.
And 2 buttons inside battery compartment
8. [°C/°F]
Toggle the temperature unit °C <- -> °F
9. [Reset]
To activate system reset to the main unit during abnormal condition which will reset all settings back to factory values.
GETTING STARTED
This In-Out thermo clock was designed for easy set up. For best operation, the following steps are required to be done
in the proper sequence.
1. INSERT BATTERIES FOR MAIN UNIT BEFORE DOING SO FOR THE SENSOR UNITS.
2. RECEIVING UNIT CANNOT BE PROGRAMMED MANUALLY UNTIL THE WIRELESS REMOTE SENSOR
UNIT REGISTRATION PROCEDURE HAS BEEN COMPLETED.
3. POSITION THE REMOTE UNIT AND MAIN UNIT WITHIN EFFECTIVE TRANSMISSION RANGE, WHICH, IN USUAL
CIRCUMSTANCES, IS 165 FEET. Although the remote unit is weather resistant, it should be placed away from direct sunlight,
rain or snow.
BATTERY INSTALLATION FOR MAIN UNIT
1. Remove the battery door;
2. Insert 2 pieces AAA size 1.5V alkaline battery as indicate by the polarity;
3. Close the battery door.
Note: Replace the batteries when the low battery indicator appears on the top-right corner of the
LCD.
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Daewoo DWS-60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Daewoo DWS-60 in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info