810366
313
Zoom out
Zoom in
Previous page
1/396
Next page
Miscellaneous situations
311
Jump start
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Connect one end of the red jump lead to
the positive + terminal of the vehicle with
the at battery A.
Connect the other end of the red jump
lead to the positive terminal + in the vehi-
cle providing assistance B.
Connect one end of the black jump lead
C to a suitable ground terminal, to a solid
piece of metal in the engine block, or to
the motor block itself.
Connect the other end of the black jump
lead D to a solid metal component bolted
to the engine block or to the engine block
itself of the vehicle with the at battery.
Do not connect it to a point near the bat-
tery.
Position the leads in such a way that they
cannot come into contact with any moving
parts in the engine compartment.
Starting
Start the engine of the vehicle with the
boosting battery and let it run at idling
speed.
Start the engine of the vehicle with the at
battery and wait for 2 or 3 minutes until the
engine is running.
Removing the jump leads
Before you remove the jump leads, switch
o the dipped beam headlights if they are
switched on.
Turn on the heater blower and heated rear
window in the vehicle with the at battery.
This helps minimise voltage peaks which
are generated when the leads are discon-
nected.
When the engine is running, disconnect
the leads in reverse order to the details
given above.
If the engine fails to start after about 10sec-
onds, switch o the starter and try again after
about 1 minute.
WARNING
Please note the safety warnings referring
to working in the engine compartment
›››page320.
The battery providing assistance must have
the same voltage as the at battery (12V)
and approximately the same capacity (see
imprint on battery). Failure to comply could
result in an explosion.
Never use jump leads when one of the bat-
teries is frozen. Danger of explosion! Even
after the battery has thawed, battery acid
could leak and cause chemical burns. If a
battery freezes, it should be replaced.
Keep sparks, ames and lighted cigarettes
away from batteries, danger of explosion.
Failure to comply could result in an explo-
sion.
Observe the instructions provided by the
manufacturer of the jump leads.
Do not connect the negative cable from
the other vehicle directly to the negative ter-
minal of the at battery. The gas emitted
from the battery could be ignited by sparks.
Danger of explosion.
Never attach the negative cable to fuel sys-
tem components or the brake lines in the
other vehicle.
The non-insulated parts of the battery
clamps must not be allowed to touch. The
jump lead attached to the positive battery
terminal must not touch metal parts of the
vehicle, this can cause a short circuit.
Position the leads in such a way that they
cannot come into contact with any moving
parts in the engine compartment.
Do not lean on the batteries. This could re-
sult in chemical burns.
Take into account the instruction manual
of the jump lead manufacturer and the in-
struction manual of the other vehicle.
NOTICE
Immediately go to a specialist workshop and
have the 12volt battery checked.
313


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cupra Formentor - 2022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cupra Formentor - 2022 in the language / languages: English as an attachment in your email.

The manual is 7.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cupra Formentor - 2022

Cupra Formentor - 2022 User Manual - German - 415 pages

Cupra Formentor - 2022 User Manual - Dutch - 424 pages

Cupra Formentor - 2022 User Manual - French - 436 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info