817289
51
Zoom out
Zoom in
Previous page
1/352
Next page
Self-help
WARNING
The factory-supplied jack* is only designed
for changing wheels on this model. On no
account attempt to use it for lifting heavier
vehicles or other loads. Risk of injury.
Make sure that the jack* remains stable.
If the surface is slippery or soft, the jack*
could slip or sink, respectively, with the re-
sultant risk of injury.
Only raise the vehicle with the jack* sup-
plied by the manufacturer. Other jacks,
even those approved for other CUPRA
models could slip, with the consequent risk
of injury.
Only mount the jack* on the support
points designed for this purpose on the
strut, and always align the jack correctly. If
you do not, the jack* could slip as it does
not have an adequate grip on the vehicle:
risk of injury!
You should never place a body limb such
as an arm or leg under a raised vehicle that
is solely supported by the jack.
If you have to work underneath the vehi-
cle, you must use suitable stands addition-
ally to support the vehicle, there is a risk of
accident!.
Never raise the vehicle if it is tilting to one
side or the engine is running.
Never start the engine when the vehicle is
raised. The vehicle may come loose from
the jack due to the engine vibrations.
CAUTION
The vehicle must not be raised on the
crossbar. Only place the jack* on the points
designed for this purpose on the strut. Oth-
erwise, the vehicle may be damaged.
Removing and installing a wheel
Change the wheel after loosening the wheel
nuts and raising the vehicle with the jack.
When removing/fitting the wheel, the rim
may hit and damage the brake disc. For this
reason, please take care and get a second
person to assist you.
Taking off the wheel
Unscrew the wheel nuts using the box
spanner and place them on a clean surface.
Take off the wheel.
Putting on the spare wheel
Check the direction of rotation of the tyre
page 49.
Place the spare wheel or temporary spare
wheel into position.
Screw on the wheel nuts in position and
tighten them loosely with a box spanner.
To tighten the anti-theft locking wheel
nuts use the corresponding adaptor.
Carefully lower the vehicle using the jack*.
Use the wheel spanner to tighten all of the
wheel nuts clockwise. Tighten the bolts in di-
agonal pairs (not in a circle).
Put the caps, trim or full hubcap back on.
The wheel nuts should be clean and turn
easily. Before fitting the spare wheel, inspect
the wheel condition and hub mounting sur-
faces. These surfaces must be clean before
fitting the wheel.
Tightening torque of the wheel nuts
The prescribed tightening torque for wheel
nuts for steel and alloy wheels is 140 Nm. Af-
ter changing a wheel, have the tightening
torque checked immediately with a torque
wrench that is working perfectly.
Before checking tightening torque, have
any rusty wheel nuts that are difficult to
screw replaced and clean the wheel hub
threads.
Never apply grease or oil to wheel nuts or to
the wheel hub threads. Even if the bolts have
been tightened to the prescribed torque,
they could come loose while driving.
Tyres with directional tread pattern
Tyres with directional tread pattern have
been designed to operate best when »
49
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cupra Formentor - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cupra Formentor - 2020 in the language / languages: English as an attachment in your email.

The manual is 5.27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cupra Formentor - 2020

Cupra Formentor - 2020 User Manual - German - 376 pages

Cupra Formentor - 2020 User Manual - French - 384 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info