73449

Cuisinart CBT 500 E Manual

7
Zoom out
Zoom in
Previous page
1/41
Next page
7
CLEANING AND MAINTENANCE
Always unplug your Cuisinart
®
SmartPower Premier
™
600-Watt Blender
from the electrical outlet before cleaning. The blender is made of
corrosion-resistant parts which are easy to clean. Before first use and
after every use, clean each part thoroughly. Periodically check all parts
before reassembly. If any part is damaged or blender jar is chipped or
cracked, DO NOT USE BLENDER.
Remove the blender jar from the motor base by lifting straight up and away.
Twist off the locking ring by turning counterclockwise.
Remove the cutting assembly and rubber gasket. Wash in warm soapy
water, rinse, and dry thoroughly.
Place the locking ring in the upper rack of the dishwasher or wash in
warm water.
CAUTION: Handle the cutting assembly carefully. It is SHARP and may
cause injury. Do not attempt to remove blades from cutting assembly.
Remove the blender jar cover and the measured pour lid. Wash in warm,
soapy water; rinse and dry thoroughly, or place in upper rack of dishwasher.
The blender jar must be washed in warm, soapy water and rinsed and dried
thoroughly. The blender jar can also be placed upside down in dishwasher.
Finally, wipe the motor base clean with a damp cloth to remove any residue,
and dry thoroughly. Never submerge the motor base in water or other liquid,
or place in a dishwasher.
Tip: You may wish to clean your blender cutting assembly as follows:
Squirt a small amount of dishwashing liquid into assembled blender jar
and fill halfway with warm water. Run on Low for 15 seconds. Repeat, using
clean tap water. Empty blender jar and carefully disassemble parts. Wash
cutting assembly, gasket and locking ring in warm, soapy water. Rinse and
dry all parts thoroughly.
DOs and DON’Ts WHEN USING YOUR BLENDER
Do:
• Make sure the electrical outlet is rated at the same voltage as that stated
on the bottom of the blender motor base.
• Always use the blender on a clean, sturdy and dry surface.
• Always add liquid ingredients to the blender jar first, then
add remaining ingredients. This will ensure that ingredients
are uniformly mixed.
• Cut most foods into cubes approximately ½ inch (1.3 cm) to
1 inch (2.5 cm) to achieve a more uniform result. Cut all cheeses
into pieces no larger than ½ inch (1.3 cm).
• Use the measured pour lid to measure liquid ingredients such as alcohol.
Replace measured pour lid after ingredients have been added.
• Use a rubber or plastic spatula as needed, only when the blender is
turned off. Never use metal utensils, as damage may occur to the blender
jar or cutting assembly.
• Place cover on firmly. Always operate the blender with the cover on.
• Make sure locking ring is tightly attached to blender jar.
• Always remove locking ring, cutting assembly, and rubber gasket before
cleaning.
• When scraping the blender jar with a spatula, remove the food from the
sides of the blender jar and place food in the center of the blender jar,
over the cutting assembly.
•
When chopping fresh herbs, garlic, onion, zest, bread crumbs, nuts, spic-
es, etc, make sure the blender jar and cutting assembly are completely dry.
• If food tends to stick to the sides of the blender jar when blending, pulse
in short bursts.
• Pulses should be short bursts. Space the pulses so the blades stop
rotating between pulses.
Don’t:
• Don’t store food or liquids in your blender jar.
• Don’t place cutting assembly and locking ring onto motor base without
the blender jar attached.
• Do not attempt to mash potatoes, knead heavy dough, or beat egg
whites.
• Don’t remove blender jar while unit is on. Keep the blender jar cover on
the blender jar while blending.
• Don't twist locking ring from blender jar when removing blender
jar from motor base. Simply lift blender jar from motor base.
• Don’t overprocess foods. Blender will achieve most desired results in
seconds, not minutes.
• Don’t overload blender. If the motor stalls, turn the blender off immedi-
ately, unplug the unit, and remove a portion of the food, then continue.
• Don’t use any utensil inside the blender jar while the motor is on.
• Don’t use any container or accessories not recommended by Cuisinart.
Doing so may result in injury.
• Don’t place hands inside the blender jar when blender is plugged in.
• Don’t add boiling liquids or frozen foods (except ice cubes or ½-inch
pieces of frozen fruit) to glass blender jar. Boiling liquids should cool for
5 minutes before being placed in blender jar.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cuisinart CBT 500 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cuisinart CBT 500 E in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info