648457
7
Zoom out
Zoom in
Previous page
1/8
Next page
EN
EN • 3
MANUAL
SAFETY
•Thechargerisdesignedforchargingonlybat-
teriesaccordingtothetechnicalspecication.
Donotusethechargerforanyotherpurpose.
Alwaysfollowbatterymanufacturers'userand
safetyrecommendations.
•Nevertrytochargenon-rechargeablebatteries.
•Neverplacethechargerontopofthebattery
orcoverthechargerwhencharging.
•Neverchargeafrozenordamagedbattery.
•NeverchargeaLi-batterywithtemperature
below0°C(32°F)ifnotspeciedbythebattery
manufacturer.
•Neveruseachargerwithdamagedcables.
Ensurethatthecableshavenotbeendamaged
byhotsurfaces,sharpedgesorinanyother
way.
•Neverplaceafan-cooledchargersothatdust,
dirtorsimilarcanbesuckedintothefan.
•Adamagedcablemustbereplacedbya
CTEKrepresentativeusinganoriginalpart
suppliedbyCTEK.Adetachablecablecanbe
replacedbytheuserusinganoriginalpartsup-
pliedbyCTEK.
•Connectiontothemainssupplymustbein
accordancewiththenationalregulationsfor
electricalinstallations.
•Chargerswithgroundedmainsplugmustonly
beconnectedtoagroundedsocketoutlet.
•Duringcharging,Lead-Acidbatteriescould
emitexplosivegases.Preventsparkscloseto
thebattery.Provideforgoodventilation.
•ChargerswithIP-classlowerthanIPx4are
designedforindooruse.Seetechnicalspeci-
cation.Donotexposetorainorsnow.
•Connectthechargertothebattery´spositive
poleandthentothenegativepole.Forbatter-
iesmountedinsideavehicle,connectthenega-
CONGRATULATIONS
tothepurchaseofyournewprofessionalswitchmodebatterycharger.Thischargeris
includedinaseriesofprofessionalchargersfromCTEKSWEDENABandrepresentsthe
latesttechnologyinbatterycharging.
4 • EN
tiveconnectiontothevehiclechassisremote
fromthefuelpipe.Thenconnectthechargerto
mainssupply.
•Disconnectthechargerfromthemainssupply.
Nextremovethenegativeconnection(vehicle
chassis)andthenthepositiveconnection.
•Dontleaveanybatteryunattendedfora
longerperiodoftimeduringcharging.Ifany
erroroccursdisconnectthechargermanually.
•(IEC 7.12 ed.5)Thisapplianceisnot
intendedforusebypersons(includingchildren)
withreducedphysical,sensoryormentalcapa-
bilities,orlackofexperienceandknowledge,
unlesstheyhavebeengivensupervisionor
instructionconcerninguseoftheapplianceby
apersonresponsiblefortheirsafety.Children
shouldbesupervisedtoensurethattheydonot
playwiththeappliance.
(EN 7.12)Thisappliancecanbeusedby
childrenagedfrom8yearsandaboveand
personswithreducedphysical,sensoryor
mentalcapabilities,orlackofexperienceand
knowledgeiftheyhavebeengivensupervi-
sionorinstructionconcerninguseoftheappli-
anceinasafewayandunderstandthehazards
involved.Childrenshallnotplaywiththeappli-
ance.Cleaningandusermaintenanceshallnot
bemadebychildrenwithoutsupervision.
EN
EN • 5
NORMAL
BATTERY
PROGRAM
ERROR LAMP
AGM
BATTERY
PROGRAM
FULLY CHARGEDREADY TO USE
RECOND
PROGRAM
SUPPLY
PROGRAM
POWER
LAMP
HOW TO CHARGE
1. Connectthechargertothebattery.
2. Connectthechargertothewallsocket.Thepowerlampwillindicatethatthemains
cableisconnectedtothewallsocket.Theerrorlampwillindicateifthebatteryclamps
areincorrectlyconnected.Thereversepolarityprotectionwillensurethatthebattery
orchargerwillnotbedamaged.
3. PresstheMODE-buttontoselectchargingprogram.
4. Followthe8-stepdisplaythroughthechargingprocess.
ThebatteryisreadytostarttheenginewhenSTEP4islit.
ThebatteryisfullychargedwhenSTEP7islit.
5. Stopchargingatanytimebydisconnectingthemainscablefromthewallsocket.
MODE-
BUTTON
TEMPERATURE
SENSOR
INDICATOR
6 • EN
CHARGING PROGRAMS
SettingsaremadebypressingtheMODE-button.Afterabouttwosecondsthecharger
activatestheselectedprogram.Theselectedprogramwillberestartednexttimethe
chargerisconnected.
The table explains the different Charging Programs:
Program
Battery
Size (Ah)
Explanation Temp range
20–300Ah
Normal battery program
14.4V/10A.UseforWETbatteries,
Ca/Ca,MFandformostGELbatteries
-20°C+50°C
(-4ºF–122ºF)
AGM 20–300Ah
AGM battery program 14.7V/10A
UseforAGMbatteries.
-20°C+50°C
(-4ºF–122ºF)
RECOND
20–300Ah
Recond program 15.8V/1.5A
Usetoreturnenergytotheempty
WETandCa/Cabatteries.Recond
yourbatteryonceperyearandafter
deepdischaretomaximiselifetimeand
capacity.TheRecondprogramadds
STEP6tothenormalbatteryprogram.
-20°C+50°C
(-4ºF–122ºF)
20–300Ah
Supply program 13.6V/10A
Useas12Vpowersupplyorusefor
floatmaintenancechargingwhen100%
capacityofthebatteryisrequired.
Supplyprogramactivatesstep7without
timeorvoltagelimitation.
-20°C+50°C
(-4ºF–122ºF)
WARNING!
The spark protection on the battery charger
is disabled during SUPPLY program.
+
+
Comfort
Connect
CONNECT THE CHARGER TO A BATTERY
Comfort
Connect
Comfort
Connect
INFO
If the battery clamps are incorrectly
connected, the reverse polarity
protection will ensure that the battery
and charger are not damaged.
For batteries mounted inside a
vehicle
1. Connect the red clamp to the battery's
positive pole.
2. Connect the black clamp to the vehicle
chassis remote from the fuel pipe and
the battery.
3. Connect the charger to the wall socket.
4. Disconnect the charger from the wall
socket before disconnecting the battery.
5. Disconnect the black clamp before the
red clamp.
EN
EN • 7
BATTERY SIZE (Ah)
TIME TO 80% CHARGED
20Ah
2h
50Ah
5h
100Ah
10h
200Ah
20h
READY TO USE
Thetableshowstheestimatedtimeforemptybatteryto80%charge
ERROR LAMP
Iftheerrorlampislit,checkthefollowing:
1. Is the chargers positive lead connected to the batterys
positive pole?
2. Is the charger connected to a 12V battery?
3. Has charging been interrupted in STEP 1, 2 or 5?
RestartthechargerbypressingtheMODE-button.Ifchargingisstill
beinginterrupted,thebattery...
STEP 1: ...is seriosly sulphated and may need to be replaced.
STEP 2: ...can not accept charge and may need to be replaced.
STEP 5: ...can not keep charge and may need to be replaced.
TEMPERATURE SENSOR
Thechargerisequippedwithatemperaturesensor.Thetemperaturesensor
willadjustthevoltagetotheambienttemperature.ForMXS10EC-the
temperaturesensorisnotdetachable.Activatedtemperaturesensorwillbe
indicatedbyalittemperaturesensorindicatorlamp.
POWER LAMP
Ifthepowerlampislitwitha:
1. STEADY LIGHT:
Themainscableisconnectedtothewallsocket.
2. FLASHING LIGHT:
Thechargerhasenteredtheenergysavemode.Thishappensifthe
chargerisn´tconnectedtothebatteryin2minutes.
TECHNICAL SPECIFICATIONS
Model number
1046
Rated Voltage AC
220–240VAC,50–60Hz
Charging voltage
14.4V,AGM
14.7V,
RECOND 15.8V,SUPPLY13.6V
Start voltage
2.0V
Charging current
10Amax
Current, mains
1.4A
rms
(atfullchargingcurrent)
Back current drain*
Lessthan1Ah/month
Ripple**
Lessthan4%
Ambient
temperature
-20°Cto+50°C,outputpowerisreduced
automaticallyathightemperatures
Charger type
8-step,fullyautomaticchargingcycle
Battery types
Alltypesof12Vlead-acidbatteries
(WET,MF,Ca/Ca,AGMandGEL)
Battery capacity
20–300Ah
Insulation class
IP65
*)Backcurrentdrainisthecurrentthatdrainsthebatteryifthechargerisnotconnected
tothemains.CTEKchargershasaverylowbackcurrent.
**)Thequalityofthechargingvoltageandchargingcurrentisveryimportant.Ahigh
currentrippleheatsupthebatterywhichhasanagingeffectonthepositiveelectrode.
Highvoltageripplecouldharmotherequipmentthatisconnectedtothebattery.CTEK
batterychargersproduceverycleanvoltageandcurrentwithlowripple.
8 • EN
STEP 1 DESULPHATION
Detectssulphatedbatteries.Pulsingcurrentandvoltage,removessulphatefromthelead
platesofthebatteryrestoringthebatterycapacity.
STEP 2 SOFT START
Testsifthebatterycanacceptcharge.Thissteppreventsthatchargingproceedswitha
defectbattery.
STEP 3 BULK
Chargingwithmaximumcurrentuntilapproximately80%batterycapacity.
STEP 4 ABSORPTION
Chargingwithdecliningcurrenttomaximizeupto100%batterycapacity.
STEP 5 ANALYSE
Testsifthebatterycanholdcharge.Batteriesthatcannotholdchargemayneedtobereplaced.
STEP 6 RECOND
Choose theRecondprogramtoaddtheRecondsteptothechargingprocess.DuringtheRecondstep
voltageincreasestocreatecontrolledgasinginthebattery.Gasingmixesthebatteryacidandgives
backenergytothebattery.
STEP 7 FLOAT
Maintainingthebatteryvoltageatmaximumlevelbyprovidingaconstantvoltagecharge.
STEP 8 PULSE
Maintainingthebatteryat95–100%capacity.Thechargermonitorsthebatteryvoltageandgivesa
pulsewhennecessarytokeepthebatteryfullycharged.
1
VOLTAGE (V)CURRENT (A)
ANALYSE RECOND PULSE
DESULPHATION SOFT START BULK ABSORPTION
15.8V
Increasing voltage
to 14.7V @ 25°C
10A
10A until 12.6V Increasing voltage
to 14.4V @ 25°C
10A
1
7
Limit:
Max 20h Max 10h 3 minutes
30 min or 4h
depending on
battery voltage
10 days
Charge cycle restarts
if voltage drops*
Charge cycle restarts
if voltage drops
Max 8h
15.8V
15.8V 10A until 12.6V
10A until 12.6V
Increasing voltage
to 14.4V @ 25°C
10A
14.4V @ 25°C
Declining current
14.7V @ 25°C
Declining current
14.4V @ 25°C
Declining current
Checks if voltage
drops to 12V
Checks if voltage
drops to 12V
Checks if voltage
drops to 12V
Max 13.6V
10A
13.6V
10A
13.6V
10A
13.6V
10A
12.7V‒14.4V
10‒2A
12.7V‒14.7V
10‒2A
12.7V‒14.4V
10‒2A
Max 8h
2 3 4 5
FLOAT
6 8
RECOND
SUPPLY
AGM
Max 15.8V
1.5A
*Supply program is not time or voltage limited.
CHARGING PROGRAM
EN
EN • 9
LIMITED WARRANTY
CTEKSWEDENAB,issuesthislimitedwarrantytotheoriginalpurchaserofthisproduct.
Thislimitedwarrantyisnottransferable.Thewarrantyappliestomanufacturingfaults
andmaterialdefectsfor2yearsfromthedateofpurchase.Thecustomermustreturnthe
producttogetherwiththereceiptofpurchasetothepointofpurchase.Thiswarrantyisvoid
ifthebatterychargerhasbeenopened,handledcarelesslyorrepairedbyanyoneother
thanCTEKSWEDENABoritsauthorisedrepresentatives.Oneofthescrewholesinthe
bottomofthechargerissealed.Removingordamagingthesealwillvoidthewarranty.
CTEKSWEDENABmakesnowarrantyotherthanthislimitedwarrantyandisnotliable
foranyothercostsotherthanthosementionedabove,i.e.noconsequentialdamages.
Moreover,CTEKSWEDENABisnotobligatedtoanyotherwarrantyotherthanthis
warranty.
SUPPORT
Fore support and more information about CTEK products: www.ctek.com, info@ctek.com,
info@ctek.se,+46(0)22535180.Forlatestrevisedmanualseewww.ctek.com.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ctek MXS 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ctek MXS 10 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ctek MXS 10

Ctek MXS 10 User Manual - German - 8 pages

Ctek MXS 10 User Manual - Dutch - 8 pages

Ctek MXS 10 User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info