736874

Crivit Inshore 335 V IAN 282780 Manual

14
Zoom out
Zoom in
Previous page
1/54
Next page
16
Monitoring the operating pressure
IMPORTANT!
The PVC material will stretch a little
following initial inflation and will never
return to its original size.
Please remember that this data can
vary slightly, depending on the cargo it
is carrying and the outside
temperature.
Pump up the air chambers
/ / so that they
feel firm to the touch and no wrinkles can be
seen in the material. Press on each air chamber
with your thumb; you should just about be able
to press the material in slightly.
Measuring strips and monitoring
ruler (Fig. H, I)
To monitor the air chamber / operating
pressure, place the 0 of the monitoring ruler
(Fig. I) over the 0 of the measuring strip
(Fig. H) on the article.
During initial inflation, the maximum stretch point
MUST NOT exceed Position A on the monitoring
ruler.
From the second use onwards, pump up the craft
so that the 10 on the measuring strip is between
Position A and Position 10 of the monitoring
ruler.
Inflating the air chambers
Floor chamber with stopper
valve
/ Lower side chamber with stopper
valve (Fig. J)
1. Open the valve closure
.
2. Pump up each air chamber.
3. Close the valve closure and press the sealed
valve down using a little pressure.
/ Upper side chamber with screw
valve (Fig. F)
1. Inflate the upper side chambers / and
seal the closure cap by screwing in a
clockwise direction.
Front seat, Rear splash guard
with seat, Prow splash guard,
Triangular cushion (Fig. K - N)
Note:
The ropes must be tied using a reef
knot and a figure-of-eight hitch knot
(Fig. K, L)
1. Front seat (Fig. M, N)
Pump up all of the air chambers. Place the seat
underneath both of the upper side air chambers
/ , so that the seat is securely fitted. Tie the
seat using the 80cm rope through the eyelet on
the floor chamber (Fig. M) as well as with
a 150cm rope in a zig-zag shape through the
eyelets on the side chambers and (Fig. N).
2. Rear splash guard with seat
Pump up all of the air chambers. Press the seat
underneath both of the upper side air chambers
/ , so that the seat is securely fitted.
Fasten the rear splash guard with seat with a
280cm rope in a zig-zag shape through the
eyelets on the side chambers and .
3. Prow splash guard
Pump up all of the air chambers and fasten the
prow splash guard with a 280cm rope in a zig-
zag shape to the eyelets on the side chambers
and .
4. Triangular cushion
Position the inflated triangle cushion securely in
the bows of the kayak, where it serves as a foot
support for the person sitting at the front.
Dismantling the kayak
Remove the front seat, the rear splash guard with
seat, the prow splash guard and the triangular
cushion.
Deflating
Deflate the kayak as follows:
1. To deflate the floor chamber
, the lower side
chambers / , the front seat , the rear
splash guard with seat , and the prow
splash guard , pull the stopper valve out
of its concealed location and press the shaft
lightly or use the deflation tube .
GB/IE
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit Inshore 335 V IAN 282780 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit Inshore 335 V IAN 282780 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info