Manual Crivit IAN 334369 1910 (page 9 of 24) (English, German, Dutch, French, Polish)

735646

Zoom out

Zoom in

1/24

9GB/IE

3. Insert the segments of the ﬁbreglass

poles (3) into one another and lay the

poles in a cross on top of the tent (Fig. C).

4. Bend the ﬁbreglass poles and put their ends

over the pins on the metal rings (1a) at the

corners of the tent (Fig. D).

5. Lift up the middle of the tent (Fig. E) and

hook each of the centre clips over one of

the ﬁbreglass poles (Fig. F).

6. Hook all the clips on the tent over the ﬁbre-

glass poles (Fig. F).

7. Stretch out the corners of the tent ﬂoor

and secure each metal ring with a ground

peg (4).

Note: insert the ground pegs into the ground at

a slight angle.

8. Pull the rain protector (2) over the ﬁbreglass

poles.

Note: make sure that the ventilation openings

are on the long sides.

9. Tie the fabric ties (2c) on the underside of

the rain protector onto the ﬁbreglass poles

(Fig. G).

10. Attach the hooks on the rain protector onto

the metal rings on the tent.

11. Tension the guy lines and attach each one

with a ground peg (Fig. H).

12. Secure the rubber loops at the bottom of

the rain protector with ground pegs.

13. Lift up the ventilation openings (2a) and

raise the spacers (2b) (Fig. H).

Use

On the inside of the tent roof is a plastic lug

on which you can hang a camping lamp (not

included in the package contents). You can use

the tent’s inner pocket for your valuables.

Opening the door

You have the option of fully opening the tent

entrance. To do this, follow the steps below:

1. Completely open the zip of the rain protec-

tor (2).

2. Roll up the fabric lengthwise into a roll.

3. Fasten it with the toggles, so it can’t unroll

(Fig. J).

4. Open the zip on the tent (1).

5. Roll up the door fabric of the tent (1) into

a roll.

6. Fasten it with the toggles near the ground

(Fig. I).

Closing the door

To completely close the tent entrance, proceed

as follows:

1. Unfasten the toggles on the tent (1) near

the ground.

2. Close the zip on the tent.

3. Unfasten the toggles on the rain protec-

tor (2) and unroll the fabric.

4. Close the zip on the rain protector.

Dismantling

Note: dismantle the tent in as dry and clean a

condition as possible, to prevent mould forma-

tion and stains.

After dismantling in the rain, let the product dry

out completely before packing it away. Clean

all components thoroughly before packing them

away.

1. Remove the ground pegs (4) (Fig. K).

2. Roll up the guy lines.

3. Release the clips and hooks on the rain

protector (2) from the ﬁbreglass poles (3)

and the metal rings on the tent (1).

4. Fold up the rain protector as far as possible

and untie the knots on the ﬁbreglass poles.

5. Pull the ﬁbreglass poles oﬀ the pins on the

metal rings and fold up the ﬁbreglass poles.

Folding pattern (Fig. K)

1. Fold the tent (1) in half longways once, and

then fold in half again.

Important: the folded dimensions must be no

longer than the length of the storage bag (6).

2. Fold the rain protector (2) to the same

maximum width as the tent and lay in on

top of the tent.

3. Place the ground pegs (4) in the bag (5).

4. Place the peg bag and the ﬁbreglass

poles (3) on one end of the tent and roll all

the parts together tightly.

Note: pay attention when rolling to the ventila-

tion opening spacers (2b) and their position.

5. Tie up the rolled product with the ties and

stow it in the storage bag.

Repairs, care and storage

Repairs

Small tears or holes in the fabric can be repaired

with standard repair patches.

Important! Do not use repair patches on

the seams.

Enquire at a specialist store about what repair

materials to use and how to use them. Follow the

manufacturer’s instructions. Larger tears should

be sewn by someone with technical skills. Broken

or defective frame parts must immediately be

replaced, and must no longer be used. Enquire

at a specialist store about suitable replacement

parts.

Stain removal

You can remove dirt on the surface and small

stains with a soft brush, or by wiping them with a

damp cloth.

Use only water and no cleaning agents,

otherwise the product’s waterprooﬁng may be

impaired.

Zip fasteners

Regularly use a silicone spray (not included

in the package contents) and apply it to the

zips to prevent unnecessary wear. Enquire at a

specialist store about a suitable silicone spray

and its use.

Preventing mould

Do not store the product wet or damp over a

long period of time. However, if light mould does

form, use a soft and slightly dampened brush or

sponge to remove the mould. Then seal the treat-

ed spot with a suitable tent fabric waterprooﬁng

agent (not included in the package contents).

Storage

When not in use, always store the product clean

and dry at room temperature to prevent the

formation of mould.

When not in use for extended periods, take the

product out of its storage bag and store it in a

dry place away from direct sunlight.

Disposal

Dispose of the article and the packaging materi-

als in accordance with current local regulations.

Packaging materials such as foil bags are not

suitable to be given to children. Keep the pack-

aging materials out of the reach of children.

Dispose of the products and the

packaging in an environmentally friendly

manner.

The recycling code is used to identify

various materials for recycling. The code

consists of the recycling symbol – which

is meant to reﬂect the recycling cycle – and a

number which identiﬁes the material.

Notes on the guarantee and

service handling

The product was produced with great care and

under constant supervision. You receive a three-

year warranty for this product from the date of

purchase. Please retain your receipt.

The warranty applies only to material and

workmanship and does not apply to misuse or

improper handling. Your statutory rights, espe-

cially the warranty rights, are not aﬀected by this

warranty.

With regard to complaints, please contact the

following service hotline or contact us by e-mail.

Our service employees will advise as to the

subsequent procedure as quickly as possible.

We will be personally available to discuss the

situation with you.

Any repairs under the warranty, statutory guar-

antees or through goodwill do not extend the

warranty period. This also applies to replaced

and repaired parts. Repairs after the warranty

are subject to a charge.

IAN: 334369_1910

Service Great Britain

Tel.: 0800 404 7657

E-Mail: deltasport@lidl.co.uk

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (oﬀ peak))

E-Mail: deltasport@lidl.ie

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Crivit IAN 334369 1910 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Crivit IAN 334369 1910 Manual

Product: