498215
9
Zoom out
Zoom in
Previous page
1/24
Next page
9
The Controls - Timed Dry Models
Setting the Timer
Starting the Dryer
Speedy Iron Cycle
Selecting the
required Heat
Switch setting
Empty Water Light
Heat Switch (OUT low heat, IN high heat) Empty Water Light
Turn the Timer clockwise to select the required drying time.
The drying time for both heat settings is controlled by the timer. All you
have to do is turn the Timer Control clockwise until the required time
appears in line with the indicator. If you have selected more time than
you require turn the knob clockwise to select the correct time required.
Never wind the timer control anti-clockwise.
The "Guide to Drying Times" section will tell you how much time you
will need for various loads.
Press and release the START Drying button to commence a drying
programme. The door must have been securely closed first.
After releasing the start button, it will return to its original position.
This is a short programme of approximately 10 minutes to condition
previously dried clothes. See section, "Speedy Iron Programme".
It consists of a period of heating followed by a short cool tumble
period. Select HIGH heat for this programme.
It should not be used on damp loads, as it is NOT a drying
programme.
To select HIGH heat (Cottons), the Heat Switch must be IN.
To select LOW heat (Acrylics and Synthetics), the Heat Switch must
be OUT. See section, "Guide to Drying Times".
This light will glow when the water container is full.
You should not wait for this light to glow before emptying the
container, but empty it after each load (See section “Emptying the
Water Container”).
NOTE: If the light glows during a programme you must stop the dryer
and empty the water container. If this is not done the timer will advance
to the Cool Tumble phase without drying the load.
The light will take approximately 10 seconds to go out after replacing
the empty container.
Start Switch
THE START BUTTON MUST BE PRESSED TO START ALL
PROGRAMMES.
NOTE: If the door is opened during a programme, the Dryer
will automatically stop. To continue the programme after
closing the door, the START button must be pressed again.
9


Need help? Post your question in this forum.

Forumrules
1

Forum

creda-t632cw

Reset search

  • dryer will not power up no voltage to the switch.. Could it be start relay failure? Door interlock seems to work O.K

    any suggestions? Submitted on 1-1-2021 at 12:47

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Creda T632CW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Creda T632CW in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info