818991
7
Zoom out
Zoom in
Previous page
1/222
Next page
4. Clean dirt and debris from all parts.
5. Align the spool tabs with the tab openings in the base of
the spool.
6. Push the spool cover until it clicks into position.
5.4 INSTALL THE CUTTING LINE
Figure 12 - 15.
NOTE
Do not put more than 15 feet of cutting line in at a time.
1. Line up the slots on the spool cap with the slots on the
trimmer head.
2. Put the cutting line through the hole. Push the cutting line
until it exits the opposite hole.
3. Pull the cutting line through until there is an equal
quantity of cutting line on each side.
4. Turn the spool cap clock-wise to wind the cutting line
into the trimmer head. Keep approximately 5 in of cutting
line above out of each side of the trimmer head.
5.5 REMOVE THE TRIMMER HEAD
Figure 16.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Remove the spool cover and the spool.
3. Loosen the nut on the trimmer head clockwise with a
wrench.
4. Remove the trimmer head.
5.6 ASSEMBLE THE TRIMMER HEAD
Figure 17.
1. Put the trimmer head onto the housing.
2. Install the nut.
3. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
4. Tighten the nut on the trimmer head counterclockwise
with a wrench.
IMPORTANT
You must install the cut-off blade when you use the trimmer
head.
5.7 ASSEMBLE THE BRUSH CUTTER
Figure 18.
WARNING
Wear gloves and be careful with sharp edges.
WARNING
Apply the guard to the blade.
WARNING
Use the specified Nylon locknut which is packed with the
blade to assemble the blade. You must change the locknut
after using it for 20 times.
1. Put the the metal rod in the specified angle transmission
hole to fix the trimmer head.
2. Put the brush-cutter blade on top of the gear box. Make
sure the blade is in the center.
3. Put the plate onto the blade.
4. Put the outer cup above the plate.
5. Put the locknut above the outer cup.
6. Tighten the lock-nut counter-clockwise with the wrench.
5.8 REMOVE THE BRUSH CUTTER
Figure 19.
WARNING
Apply the guard to the blade.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Loosen the nut clockwise and remove the outer cup.
3. Remove the plate and brush-cutter blade.
6 TRANSPORTATION AND
STORAGE
6.1 MOVE THE MACHINE
When you move the machine, you must:
Wear gloves.
Stop the machine.
Remove the battery pack and charge it.
Assemble the blade guard.
6.2 STORE THE MACHINE
Remove the battery pack from the machine.
Make sure that children cannot access the machine.
Keep the machine away from corrosive agents such as
garden chemicals and de-icing salts.
Secure the machine during transportion to prevent
damage or injury. Clean and examine the machine for any
damage.
7
English EN
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82TB20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82TB20 in the language / languages: All languages as an attachment in your email.

The manual is 4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info